A hydraulic press has an input cylinder 1 inch in diameter and an output cylinder 6 inches in diameter. Assuming 100% efficiency. The force exerted by the output piston when a force of 10 pounds is applied to the input piston is

A hydraulic press has an input cylinder 1 inch in diameter and an output cylinder 6 inches in diameter. Assuming 100% efficiency. The force exerted by the output piston when a force of 10 pounds is applied to the input piston is

Name: Not yet answeredMarked out of 2.00P Flag questionA hydraulic press ha
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Not yet answeredMarked out of 2.00P Flag questionA hydraulic press has an inputcylinder 1 inch in diameter and anoutput cylinder 6 inches in diameter.Assuming 100% efficiency. The forceexerted by the output piston when aforce of 10 pounds is applied

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hoist in a factory lifts a steel load of mass 5 tons to a height of 25 m. The overall efficiency of the hoist is 65% and the input power to the hauling motor is 100 kW. Calculate the time taken for lifting operation.
explained please
A steam catapult is used to assist the acceleration of aircraft from standstill to flight speed in a very short distance. Steam is admitted to the cylinder and steam pressure acts on a piston sliding in a cylinder. The force produced is transmitted to the aircraft by means of a suitable linkage. a) Determine the work done by the steam on the piston if steam is admitted to the cylinder at 20 bar throughout the 25 m stroke. The piston diameter is 500 mm. It may be assumed that the process is reversible. (Ans: W = 9.817 MNm or MJ) m %3D b) In some instances steam is admitted for part of the stroke only and thereafter the fixed mass of steam in the cylinder expands to a reduced pressure. If steam is admitted at 20 bar for 60% of the stroke, the pressure falling linearly to 4 bar over the remainder of the stroke, sketch a diagram of steam pressure against volume and determine the new work done. (Ans: W = 8.24 MJ)
Calculate the work produced by the 25-N force at an angle 30 degrees from the horizontal which resulted to a 15m displacement.Kindly answer with complete solution please. Needed ASAP.
Task 2 Given the following data: - Clearance volume of 70 cm3 - The bore of cylinder is 130 mm - The stroke of compressor is 70 mm -The measured low and high pressures are 120 and 700 kPa, respectively. - The volume before and after compression are 998.66 and 243.6 cm3, respectively. 1. Determine the volumetric efficiency of a reciprocating compressor 2. Calculate the isothermal and polytropic work of a reciprocating compressor 3. Evaluate the isothermal efficiency
The Stroke of a gas engine which works on the constant volume cycle is 488 mm. The pressure at the beginning of the compression is 0.72 bar and at the end of compression is 13.65 bar. Assuming compression follows the law PV^1.36 = C, Calculate the clearance between the piston and cylinder cover at the end of compression in mm of length.
The ram and plunger of a hydraulic press are 150 mm and 25 mm in diameter respectively. With a plunger stroke of 30 cm, the press is able to lift a load of 1 tonnes through 1.5 m in a times of 25 min. Area of the plunger 9.54 cm2 11.21 cm2 4.91 cm2 O 6.82 cm2 O
I need the answer as soon as possible
Two blocks weighing 600lbs and 400lb shown in Figure 3 are to be moved to the right by the block weighing W, lb. The pulleys are assumed to be frictionless while f = 0.10 for the blocks. Determine the weight W in pounds (lbs) to start the system. 400 lb 600 lb W lb 30 Figure 3
Find the value of work done is 410 J and displacement is 32 m. Find the force applied ?