A hydraulic press for compacting powdered samples has a large cylinder which is 10.0 cm in diameter, and a small cylinder with a diameter of 2.0 cm. A lever is attached to the small cylinder as shown in (Figure 1). The sample, which is placed on the large cylinder, has an area of 4.0 cm?. Part A What is the pressure on the sample if F = 270 N is applied to the lever? Express your answer to two significant figures and include the appropriate units. ? P = Value Units Submit Request Answer Figure 1 of 1 Provide Feedback

Q: Why are three views used to show the object?

A: As we all now everything around us can geometrically be defined in the cartesian coordinate system.

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: the effect of scratching the of the iron sheet surface with different objects

A: Effect of scratching the of the iron sheet surface with different objects.

Q: How should gravity and movement be reflected when drawing a character for a video game?

A:

Q: Mr. Ahmed want to buy pump bodies for his company, he selected the gray cast iron as a material…

A: Solution:

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: What is the temperature of an object where it is half as hot as 80 degrees Fahrenheit?

A: The temperature is 80°F The temperature of an object is half of the given temperature.

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: Where did the 0.10472 rad/s come from?

A:

Q: what happened with the 10 in the first equation?

A:

Q: I need answers to questions 7, 8, and 9 pertaining to the print provided. Note: A tutor keeps…

A: In general revision changes are indicated in two methods.Cloud method- the recent change information…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

A:

Q: Please give the details explanation of the answer

A:

Q: That is the answer I have and it is marked as wrong, could you please do it again and see if you get…

A:

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: This was not correct may you please

A:

Q: what is the actual area in part a ?

A: Given: Q=5000 m3/min=5000m3min×1min60 sec=83.33 m3/s V=6.0 cm/s=6.0cms×1m100cm=0.06 m/s

Q: How did you get the values for Sc=Sb and Sa=Sd

A: To get the values of enthalpy and entropy at various points we have to consider the properties table…

Q: how do i draw sectional view of this object.

A: A sectional view of an object is used to identify the parts interior construction of a part…

Q: What is the degree of freedom of the two questions

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: (d) If values of M and I were known, explain how the information in the graphs could be used to…

A: Refer subpart (c) for the description of the height H of the block m. Understand that from the graph…

Fire safety

Fire safety is a new domain emerged in the early 90s to enable the design of buildings, structures, and infrastructure against destruction through fire. It also includes the provisions of building codes. This field is mostly associated with the design and efficient planning of a building, to reduce the destruction caused by fire. The branch of engineering that deals with it for the safety of the buildings from destruction of fire, is known as fire safety engineering.