A hydraulic press cylinder has an internal diameter of 30 cm and is designed to work at a 10 MPa pressure. Considering that the cylinder's construction material must not be stressed beyond 20 MPa, determine the thickness and stresses at the inner and outer radius of the cylinder. Plot the variation of the radial and hoop stresses across the thickness of the cylinder's wall.

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: A datum when used in manufacturing is primarily used for?

A: A datum in manufacturing is defined as the origin point, plane, or axis from which the geometric…

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: I require a gap of .03 min and .06 max between the 2.50 dim and the B dim (at the bottom). I apply a…

A:

Q: The last 3 compartments in a feature control frame provides the datum references; this is known as…

A: The last 3 feature control frame provides the datum referances, this is known as datum order of…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: In the following figure, add the tolerance zone and limits of size for both parts.

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: Using the Metric Full Scale Below, what is the red dimension below to the nearest Millimeter? .01…

A: Steps

Q: Draw a sectional front view, top view and side view for Hexagonal bolt (M d mm *L mm)?

A: Given Hexagonal Bolt To find Sectional front view Sectional top view Sectional side view

Q: I need help answering these 3 parts. 1. The size description of an object on the print can best be…

A: The size description of an object on the print can best be described as dimensioning.The correct…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Q: 1. What is the philosophy of the Go and No-Go gauging? Explain in some details (need schematics) 2.…

A:

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: is a measure of sensitivity of a strain gauge and is represented as the ratio of to A. BSF,…

A: Strain gauges are the devices which are used to measure the stresses in equipments or parts.