Answered: A hydraulic lift is to be used to lift…

Name: A hydraulic lift is to be used to lift a5000-lb weight by putting a w
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A hydraulic lift is to be used to lift a5000-lb weight by putting a weight of50 lb on a piston with a diameter of 0.50ft. Determine the diameter of the pistonon which the weight is to be placed.Select one:O a. 1.0 mO b. 2.11 mO c. 2.04 mO d. 1.52 m

Engineering

Mechanical Engineering

A hydraulic lift is to be used to lift a 5000-lb weight by putting a weight of 50 lb on a piston with a diameter of 0.50 ft. Determine the diameter of the piston on which the weight is to be placed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the total force in kN on a circular plate of diameter 1.5 m which is placed vertically in water in such a way that center of the plate is 2 m below the free surface of the water. Include the diagram in your solution. a.103.0 b.59.34 c.44.14 d.35.67
A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If the tree has a mass of 3 tonne (i.e. 3 metric ton), for the position shown 180 C B 1080 2250 2040 720 Determine the bar the pressure in hydrauliç cylinder AB. Answer:
A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left limb is open to the atmosphere and the right limb is connected to the pipe. The center of the pipe is 66 mm below the level of mercury in the left limb. If the difference of mercury level in the two limbs is 136 mm, determine the gauge pressure of the oil in the pipe in Pascal. The specific gravity of the oil & mercury is 0.75 and 13.6 respectively. Solution: (i) Density of oil in kg/m3 Answer for part 1 (ii) Density of mercury in kg/m3 Answer for part 2 (iii) Height of the Oil in the right limb (in meters of oil) h1 Answer for part 3 (iv) The gauge pressure of the oil in the pipe in (in Pascal)
Prob. 10: A hydraulic lift is to be used by putting a weight of 25 kg diameter of 10 cm. Determine the diameter of the piston on which the weight is to be placed. Weight 2500 kg lift a 2500 kg weight on a piston with a 10 cm of A sof. Dr
A triangular plate with base 6 m and height 2 m is submerged vertically in water such that the highest vertex of the plate is 6 meters below the surface and the base is horizontal to the surface. 6 m 6 m 2 m Express the hydrostatic force against one side of the plate as an integral and evaluate it. (Round your answer to the nearest whole number. Use 9.8 m/s2 for the acceleration due to gravity. Recall that the weight density of water is 1,000 kg/m3.)
A cargo truck with a weight of 289kN was raised using a hydraulic press. If oil acts on piston with 473mm diameter. Determine the pressure in kPa under the piston.
side the cylinder. (123.35kPa) Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the gage is 80kPa, determine the distance between the two fluid levels of the manometer 1.9 if the fluid is (a) mercury (p-13600kg/m') or is (b) water (p=1000kg/m). 1 10 The level of the water in an enelosed water
A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left limb is open to the atmosphere and the right limb is connected to the pipe. The center of the pipe is 60 mm below the level of mercury in the left limb. If the difference of mercury level in the two limbs is 137 mm, determine the gauge pressure of the oil in the pipe in Pascal. The specific gravity of the oil & mercury is 0.88 and 13.6 respectively. Solution: (i) Density of oil in kg/m3 (ii) Density of mercury in kg/m3 (iii) Height of the Oil in the right limb (in meters of oil) h1 (iv) The gauge pressure of the oil in the pipe in (in Pascal)
The 500-kg load on the hydraulic lift shown in the figure on the right is to be raised by pouring water into a thin tube. Determine how high h should be in order to begin to raise the weight
A bicycle tire pump has a piston with area 0.44 inches squared. If a person exerts a force of 30 lb on the piston while inflating the tire, what pressure does this produce on the air in the pump? Give your answer in psi.
A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left limb is open to the atmosphere and the right limb is connected to the pipe. The center of the pipe is 56 mm below the level of mercury in the left limb. If the difference of mercury level in the two limbs is 155 mm, determine the gauge pressure of the oil in the pipe in Pascal. The specific gravity of the oil & mercury is 0.81 and 13.6 respectively. Solution: (1) Density of oil in kg/m3 (ii) Density of mercury in kg/m3 (iii) Height of the Oil in the right limb (in meters of oil) h (iv) The gauge pressure of the oil in the pipe in (in Pascal)
For the hydraulic jack shown, find the load W that can be lifted by the large piston when a forceof 400N is applied on the small piston. Assume specific weight of the liquid in the jack to be 9810N/m3.