A circular tank of diameter 1.25 m contains water up to a height of Sm. An orifice of 50mm diameter is providedat its bottom. If Cd is 0.62, Solve for the height of water above the orifice after 1.25 minutes and 17 minutes.

Given: The diameter of the tank is d=1.25 m. The height of the water initially is h1=5 m. The…

Answered: A circular tank of diameter 1.25 m…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.) A glass tubing consists of 5 vertical stems which are 500 mm apart connected to a single horizontal tube. The tube is filled with water to a depth of 500 mm in the vertical stems. How fast should it be rotated about and axis through the middle stem to just zero the depth of water in that stem? Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Show the solution
FOLLOW INSTRUCTIONS AND ANSWER TYPEWRITTEN AND COMPLETELY FOR UPVOTE
The tank shown in figure is fabricated from 10 mm steel plate.
a bubble from the bottom of the river is 2 cubic feet diameter while it rises at the surface of the water from a depth of 20 feet, what is the volume/size of the bubble when it reaches the surface of the water? this is the complete question given.
A FLUID OCCUPIES 3.5m^3. IF IT HAS A MASS OF 2500 kg. CALCULATE THE SPECIFIC WEIGHT .
Formula to be used: Where: Please take note! Calculating Pressure in a Static Fluid or P = pgh or P = yh p is the fluid's density (kg/m³ or lbm/ft³) g is the acceleration due to gravity y is the specific weight of the fluid (N/m³ or lbf/ft³) W is the weight of the fluid (N or lbf) A is the area of the bottom of the vessel containing the liquid (m² or ft²) h is the depth/height of the fluid (m or ft) P = P = 1248 h that will be used for the formula may be different from the given height of liquid in a problem. Refer to the sample problem below for clarification on this matter. Sample Problem For the dam shown on the right, find the pressure at point 20 feet below the surface of the water. Solution: Here, we will not use h = 40 ft since we are asked to compute the pressure at point 20 feet below the surface of the water. So, here is the appropriate approach to this problem. P = yh The specific weight of water is 62.4 lbf/ft³. lbf P = (62.4 ft3) (20 ft) lbf ft² 40 ft 20 ft
A droplet having a diameter of 0.0762 mm if it is equivalent to an air-water interface giving a surface tension of 0.0730 N/m. a. What is the difference in pressure between the inside and outside of a droplet in N/m²? b. Compute the pressure in kPa. c. Compute the force due to surface tension in N.
Find height of water column corresponding to pressure of 33 KN/m2
Solve correctly please. (Gpt/Ai wrong ans not allowed) Your company is drilling a deep oil well in Texas. Fluids pressure encountered in that well at 15000 ft was 10000 psig. Compute the minimum required density needed to drill safely and prevent a blowout. Express your result in Lbm/gal since these are the required units in the oil field. Show explicitly your handling of units.
A hydraulic press is used to raise an 80 kN cargo truck. If oil of specific gravity 0.82 acts on the piston under pressure of 10Mpa. What is the diameter of piston required?
QV: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A circular tank of diameter 1.25 m contains water up to a height of Sm. An orifice of 50mm diameter is provided at its bottom. If Cd is 0.62, Solve for the height of water above the orifice after 1.25 minutes and 17 minutes.