A Hybrid Electric Vehicle (HEV) can be described using transfer function below. 0.04 T(s)= 82+0.04 As a control engineer you are assigned to analyze and improve the performance of the system by identifying the parameter and solving the problem given below. (NOTE: write NAN if the answer is not available). i) Natural frequency, Wn = ii) Damping ration, = iii) Setting time, T, = %3D

A Hybrid Electric Vehicle (HEV) can be described using transfer function below. 0.04 T(s)= 82+0.04 As a control engineer you are assigned to analyze and improve the performance of the system by identifying the parameter and solving the problem given below. (NOTE: write NAN if the answer is not available). i) Natural frequency, Wn = ii) Damping ration, = iii) Setting time, T, = %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

DC DC Converters a) A step-up PWM converter has the following data: V = 8 V, Vo = 24 V, lo = 1.25 A, and f = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Then, determine the required capacitance for the converter. Assume n = 100 %. b) Design a boost SMPS converter to meet the following specifications: V = 80 V, Vo= 400 V, R. = 480 n, f.= 25 kHz, VNOS 1%. Find L, C, minimum inductor current lupin), maximum inductor current tunan), and output power. Then, sketch the inductor voitage and current waveforms for one cycle.
4. ( Determine the output C using signal flow graph. Show step-by-step solution and equivalent signal flow graph in each step. Show step by step and complete solution. R G₁ H₁ G₂ H₂
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/2. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state: i. Draw the converter circuit. ii. Determine the inductor's turn ratio. iii. Determine the primary inductance. Sketch the diode current and switch current. iv V. Find the peak and mean of the switch current.
10. To what value must R be adjusted in Figure 3–75 to make Iz = 40 mA? Assume Vz = 12 V at 30 mA and Zz = 30 N. 11. A 20 V peak sinusoidal voltage is applied to the circuit in Figure 3–75 in place of the de source. Draw the output waveform. Use the parameter values established in Problem 10. > FIGURE 3-75 R VIN 18 V
1 of 1 Discuss the process of Nyquist Criterion as applied to open-loop function. В I Σ II II ... DI II
Problem 3.41.3- A system is shown below in figure for this system find the transfer function relating displacements y and x and also draw relating mechanical circuit diagram. A fit) K
Electrical Engineering (le:5.D20) You have a 100 mV signal in the frequency range 600 Hz to 700 Hz with which you want to drive a 2002 load. Unfortunately, there is a comparable amount of "line noise" at 60 Hz. You are told that the output impedance of the signal source is 300 2. Design a circuit that will reduce the noise to no more than 20% of the signal and be able to drive your load. You need to specify the power supply voltage and the component values, but you may assume that "reasonable" transistors. you have
Electrical Engineering _ Power Electronics Notes: pls try to answer in less than 30 min.
Consider the following step up converter with a resistive load of value RS ohms. it is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is5 kHz and the duty cycle k is first set to 05 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. if the average supply current is BOA then the average load current is: Select one: O a. la 80A O b. la 40A O cla 50 A O d. la 81 A
how to solve q12.
Discuss about the inversion technique. DSP subject
1b