a horizontal venturimeter with inlet and throat diameters 160 mm and 60 mm respectively is used to measure the flow of an oil of specific gravity 0.8. If the discharge of the oil is 0.05 m3/s, find the deflection of oil mercury gauge. take venturimeter constant = 1

Q: Oil is flowing through the venture meter shown in the figure. The water velocity in the main pipe of…

A:

Q: A pitot tube directed into a water stream having a velocity o 2.7 m/sec. It has gauge difference of…

A: Given:v=2.7 m/sx=30 mm =0.03 m

Q: Speed Flow Rate: 6500 L/s Ruler Presure Units Metric OEngish 101.302 kPa OFriction OFlux meter Dots…

A:

Q: Give the classification of flow meters

A: Flow meters can be classified into two categories - Mass flow meters Volume flow meters

Q: 1) At the instant the valve is opened, the Venturi meter indicates a pressure difference of 735 kPa.…

A:

Q: Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the…

A:

Q: The air is measured at 30 deg. C and 518mm Hg. The duct diameter is 585 mm while the discharge…

A:

Q: termine the discharg

A: for the other end to open to the atmosphere the net headloss in the pipe should be equal to 3m this…

Q: Q2/ A hydraulic hose with an internal diameter of 2.5 inches. It is carrying an oil ISO 68.With…

A:

Q: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure…

A: First we calculate the diameter at outlet and inlet  D1= 8 in(1/12 ft)=2/3 ft D2=6 in(1/12ft)=0.5 ft…

Q: A Venturi meter with a 15 cm I.D. at inlet and 10 cm I.D. at throat is laid with its axis horizontal…

A:

Q: The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type mercury…

A: we have to evaluate which pitot tube will be more accurate

Q: From pump 1.0 m 1.5 m a. Using a vertical bar chart, plot the pressure drop (i.e. P₁-P₂) for these…

A:

Q: À venturimeter is inserted a 150 mm dia If the differential head indicated by the rate of flow is 80…

A:

Q: 25 mm inside diameter,

A: Given that, a=45 mm,b=103 mm,c=48 mminside radius, r=25 mmthickness of cricular hole, t=25 mm,

Q: A 300mm * 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

A:

Q: A fluid with a specific weight of 78.5 lb/ft³ and dynamic viscosity of 0.638 lbs/s-ft is flowing at…

A:

Q: Consider the following pipe system. The three water-filled tanks are connected by pipes with…

A: Given dataD1=0.10mν=1×10-6m2/sQ=0.028cms

Q: A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5

A:

Q: Water is flowing through a pipe of diameter 200 mm with a velocity of 3 m/s. Find the to friction…

A: Given:diameter of pipe=200 mmd=0.2 mvelocity, V=3 m/sLength of pipe, L=5 mfriction coefficient,…

Q: (b) A venturi meter with diameter at inlet D, and throat diameter D2, is used for measuring the flow…

A:

Q: The primary function of the venturi meter is to measure flow rate. Show that the venturi meter in…

A:

Q: The flow is said to be steady when the: For the Velocity at any point of observation does not change…

A: Introduction A fluid's flow is steady when its velocity, pressure, and all parameters of its…

Q: 4: A 60 mm diameter sharp edged orifice is placed in a pipe line to measure flow rate. If the…

A:

Q: Problem 3. Outcome 5. Please show all work. Air at standard pressure but with T = 50°C flows through…

A:

Q: In order to measure the air speed in a pipe of radius R, you construct a device which tapers the…

A:

Q: List 2 types of flow meters, describe their function along with a schematic diagram and state their…

A:

Q: B1. A crude oil of specific gravity 0.9 is flowing through a pipe of diameter 375 mm and the…

A: Given data: Write the expression to calculate the density of oil.

Q: The three tanks shown in the figure below are connected by new cast iron pipes (ɛ = 0.26 mm). The…

A: Given: To Determine: Flow rate in pipe 2 and 3 and required  pump power.

Q: 2. Given the figure below, solve for flow rate in the venturi meter. (C = 0.984) Ø= 400mm 2 (Ø =…

A:

Q: Question 2 A valve is used to regulate flow in a water pipeline. The pipe has a diameter of 400 mm…

A: Given: Diameter of the pipe→D=400 mm=0.4 m Length of the pipe→L=2500 m (1) Effect of the water…

Q: 1. Oil with a density of 910 kg/m³ and viscosity of 0.0019 m²/s is pumped through a 150 mm diameter…

A: Given data: Density of oil = ρ = 910 kg/m3Viscosity of oil =µ = 0.0019 m2/sDiameter of pipe = D =…

Q: Q1: If flow rate in pipe shown is (0.5m'/s) find the (H). H. water D=300 mm

A: Given data Volume flow rate = Q = 0.5 m3/sDiameter of pipe = 300 mm = 0.3 m

Q: Inside a pipe with a constant cross section, water flows. Calculate the total number of lost heads…

A:

Q: A pitot tube is inserted in an air flow at 20 C . The dashed lines represent mercury with a specific…

A: Given: The height difference is: ∆h=30 mm. The specific gravity of the mercury is: SGHg=13.6. The…

Q: Find the discharge of the pipe of diameter 20 mm with the velocity of water 5.25m/s in litres/sec…

A:

Q: аз in. IS installed in a 6 in. pipe-line. The pressure at the entrance to the meter is 10 psi gauge…

A: A venturi meter(diameter) =3 ininstalled in =6 inA1V1=A2V2π4×6122×v1=π4×3122×v2v1=0.25 v2v2=4 v1…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.