Answered: A horizontal pipe of cross-sectional… | bartleby

Related questions

Question

A horizontal pipe of cross-sectional area 0.29 m2 at height 6 m carries water at speed 1.9 m/s. The
pipe turns upward and levels out again to horizontal at height 14 m, where the pipe narrows to 0.11
m. If the pressure is 202 kPa at the original height, what is the pressure in kPa at the final height?
The density of water is 1000 kg/m3.
kPa

Expert Solution

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A water pipe having a 2.84 cm inside diameter carries water into the basement of a house at a speed of 0.940 m/s and a pressure of 204 kPa. If the pipe tapers to 1.82 cm and rises to the second floor 6.82 m above the input point, what are the (a) speed and (b) water pressure at the second floor? (a) Number Units (b) Number Units
A tank holds a large amount of water. A pipe is connected to the tank at the upper end and is open to the air at the lower end (see figure).The upper end of the pipe has a diameter of 17.0 cm. The lower end of the pipe has a diameter of 6.80 cm. The flow rate of the water in the pipe is 0.0500 .What is the speed of the water at the lower end of the pipe?
U-shaped tube, open to air on both ends, contains oil. Water is poured into the left arm until the water column is 10 cm deep. What is the height of the oil column (in cm) when the system is in equilibrium? The density of oil is 801 kg/m3
A water pipe having a 2.31 cm inside diameter carries water into the basement of a house at a speed of 0.945 m/s and a pressure of 187 kPa. If the pipe tapers to 1.03 cm and rises to the second floor 7.30 m above the input point, what are the (a) speed and (b) water pressure at the second floor? (a) Number i Units (b) Number i Units
A water pipe having a 2.59 cm inside diameter carries water into the basement of a house at a speed of 0.770 m/s and a pressure of 213 kPa. If the pipe tapers to 1.31 cm and rises to the second floor 6.71 m above the input point, A) What is the speed of the water at the second floor? B) What is the water pressure at the second floor?
Water is carried through a pipe. At point A, the diameter is 20 cm and the pressure is 130 kPa. At point B, which is 4.0 m higher than point A, the diameter is 30 cm. If the flow is 0.08 m^3/s, what is the pressure at the second point? 9.3 kPa Not any of the choices listed 93 Pa 0.92 atm 930 mmH20
A hollow plastic cube of side length 80 cm is held below the surface of a lake by a cord anchored to the bottom of the lake. The cube has a mass of 85 kg and the density of the lake water is 1025 kg/m. a) What is the buoyant force exerted on the cube by the lake water? b) If the top surface of the cube is 25.4 m below the surface of the lake, what is the gauge pressure at the top surface of the cube? P. = 1.013 x 10 Pa. atm c) What is the force on the top face of the cube? Note the top face will have a square cross section and the length of the side is 80 cm.
A container with water is pressurized and attached to a hose. The pressure inside the container, P, is set so that when the end of the tube is 4.5 meters above the water level in the container is ejected at 3.5 m/s. The reservoir in the container is large enough that you can ignore the change in height of the water in the container. What is the pressure P in atmospheres?
A water pipe having a 2.20 cm inside diameter carries water into the basement of a house at a speed of 0.792 m/s and a pressure of 240 kPa. If the pipe tapers to 1.44 cm and rises to the second floor 6.14 m above the input point, what are the (a) speed and (b) water pressure at the second floor? (a) Number i (b) Number i Units Units
A tall cylinder contains 25 cm of water. Oil is carefully poured into the cylinder, where it floats on top of the water, until the total liquid depth is 40 cm. What is the gauge pressure at the bottom of the cylinder?
Water travels through a pipe at 11.1 m/s. The pipe expands from a crossectional area of 1.5 m2 to an area of 12.0 m2. What is the speed of the water in the second part of the pipe in m/s? How much is the pressure change in KPa as the pipe expands? The density of water is 1000 kg/m3. Enter a positive value for an increase in pressure, a negative value for a decrease.