A horizontal bar, 10 ft long and of negligible Weight, rests on the inclined planes as shownin Fig. If the angle of friction 1s", how.close te B. fhe 200-1b force be opplied before may motion impends? loo lb 200lb

Q: Find the hydrostatic force, diveteón on the inclined ond positión of CP) sucb merged surface as…

A:

Q: Cablen #1] Compute for the resultant of the given concurrent force system 30KN 12 KN 25KN 715° 3…

A:

Q: Byusing ConjugateBeam Method, Determinethedeflection 3mtotheleftofrollersupport. 30 kN/m 55 kN 9 m 3…

A: When at any point we draw the tangent, movement at that point is termed the rotation of that point,…

Q: ORAW N,V AND M FOR THE FRAME LOADED AS SHOWN BELOW.

A: Shear force and bending moment diagram given below

Q: Q3) For the circular arch shown in the figure, compute the value of "P" such that the vertical…

A:

Q: For the beam shown, calculate the beam deflection at A. Assume that a = 4.7 ft, b = 7.1 ft, c = 9.4…

A: By method of constant deformationVA1=WL48EI       =950×4.74×12×12×128×550000×103      =0.182…

Q: Find support reaction

A: Introduction : The given structure is truss structure . It has two support one pinned and one roller…

Q: For the beam shown; 1. Determine the cquations of slope and deflection. 2. Determnine the slope and…

A: Fixed end moment at point D -  MD = 2×2×2 + 22 + 8×4 - 6⇒MD = 38 KN-m   Vertical force at point D -…

Q: For the overhanging beam, determine (a) load; and (b) the maximum value of Ely E Function. 24 kN

A:

Q: ) For the circular arch shown in the figure, compute the value of"P" such that the vertical…

A:

Q: SFD and BMD. Locate points of cont the elastic curve and compute the de 8 kN 8 kN 20 kN-m C

A:

Q: SLIDES 7-12: 30EI

A:

Q: What control is used to determine the elevation drop across the following manhole?

A: Manholes are those which are provided underground to inspect, modify and clean a sewerage system.

Q: The power uwinch A holsts the 565kg log up the 35° Incline at a constant speed of 1.25m/sec. If the…

A: Given : Weight, W = 565 × 9.81 = 5542.65 NAngle of inclination, θ = 35°Velocity, v = 1.25…

Q: Draw the FBD of  A and B when the wedge B impends to slide to the left. Friction is negligible…

A: FBD of A FBD of B

Q: Problem 1: The Box Column uses W14x370 and 1" Plate. What is the Moment of Inertia in both Ix and ly…

A: Given data,column W14x370findmoment of inertia both ix and Iy

Q: Construct influence lines and determine ordinates and slopes for given reactions, shears, and…

A:

Q: Find roller support reaction

A: Given data : The data of point load are: Point load=P Point load=Q Point load=R   Required : Finding…

Q: Question 1. Determine the vertical deflection under the load and point D of the beam shown in the…

A: Given data:

Q: 14 34 180 16 !!!! 8ft 12/5 lb 4 ft 73 lb/ft Determine a. location of maximum deflection. b maximum…

A: The given beam is a statically determinate beam and can be analyzed using the equations of…

Q: : Using unit load method find the rotations at C

A: ###Determination  of Rotations At C ###Using  Unit load method##

Q: Ex:-@ Find the END Moment by slope. deflection equation

A: Fixed End Moment:MFAB=MFBA=0MFBC=-wL212=-36×5212=-75 kN.mMFCB=wL212=36×5212=75 kN.mMCD=-36×1×0.5=-18…

Q: Slock A wieght lo KN and block B wteght 20 KN, the coeficiet of friction between Block A and Bis O.4…

A:

Q: Calculate the magnitude of the tension T and the angle 0, for which the eye bolt will be under a…

A:

Q: the pe ble ultimate moment capacity of a rectangular beam reinforced for tension only having the…

A:

Q: Design an axially loaded short square tied column for Pu 2600 kN if fe 28 MPa and fy 350 MPa.…

A: Given data, Pu = 2600 kN fc' = 28 MPa fy = 350 MPa p = 0.02

Q: BET FRMINE THE SLOPE KT A AND DEFLECTION AT C OF THE OVER HAWC BEAM エ= 45.5 lok) E= 200 GPa 36 KN-M…

A:

Q: For the propped beam shown determine the folicwing Max deflect'on Маx shear Maxirmum mornent 5kN/m…

A:

Q: I need the answer as soon as possible please. If the coefficient of static friction at the contact…

A: sofA=0.4NAfB=0.4NBApply moment at A∑ MA=0NBsin4512-0.4NBsin4512-75d=0.........1

Q: H.W: determine the magnitude of the resultant and the direction measured from the horizontal line. 8…

A: Direction Of force FA  is not given Assume Direction of force FA  from vertical is 50°Then foce on…

Q: USE SLOPE DEFLECTION METHOD. From the indeterminate beam shown, find the fixed end moment at A & D,…

A:

Q: 1. Determine the Degree of Freedom of the following Structure

A: We know that,Degree of freedom in a truss is giben byDOF=2j-rewhere,j=Number of joints re= Total…

Q: SITUATION 2 Using the Portal Frame Method: 36 kN .B 10m 8m A 21-25) Determine the Shear force on…

A:

Q: Determine FEMAB of the beam with uniform varying load of 23 kN/m, 1 meter from the left fixed…

A:

Q: urrent Attempt For the cantilever steel beam [E- 230 GPa; I- 95 x 10 mm*), use the…

A:

Q: %06 O Take Quiz Exit Assume the area of the interior columns is twice the area of the exterior…

A:

Q: Compute the moment of inertia for the built up secion shown below about the strong axis only

A: To determine the moment of inertia of the given cross-section about the strong axis.   The strong…

Q: What is the loss due to shrinkage for a pre-tensioned beam under humid condition? O a. 2.1 MPa O b.…

A: Given data: pre-tensioned, L=12.5 m Slip=15 mm Humid Condition

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.