A hook as shown in figure 2 is a symmetrical trapezium of 50 mm deep, the inner width being 60 mm and outer being 30 mm. Calculate the extreme intensities of stress at points A and B, when the hook carries a load of 30 kN, the load line passing 40 mm from the inside edge of section and the center of curvature being in the load line.

A hook as shown in figure 2 is a symmetrical trapezium of 50 mm deep, the inner width being 60 mm and outer being 30 mm. Calculate the extreme intensities of stress at points A and B, when the hook carries a load of 30 kN, the load line passing 40 mm from the inside edge of section and the center of curvature being in the load line.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft of diameter d is guided in rotation at A (bearing 1) and C (bearing 2) and carries two wheels supporting the indicated loads, The radius of wheel B is 200 mm, and of wheel D is 100mm. The shaft is made of steel. F2 = 6000 N. Dimensions are in mm. Calculate the diameter (mm) of the shaft considering an allowable stress of 270 MPa for a stress composed of bending and torsion.
Ql- Compare the maximum stress induced into a rectangular plate 100mm long into x-axis direction, 50mm width into y-axis direction and 10mm thickness into z-axis direction is subjected to tensile load of 10kN into y-axis direction for bellow cases: 1- As a solid plate. 2- The same plate with a Circle hole 10mm diameter in xy-plane in the center the plate.
A steel column of hollow circular cross section shown in Figure is supported on a circular steel base plate and concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
I need answer please in 10 min with my best wishes
Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)
indicate given, solution and box final answer
3. A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line. 4. The bar in Q3 is also subject to a tensile load of 15kN applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
question is on the figure
4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and the material is class 50 gray cast iron. Determine maximum tensile stress and factor of safety for clamping force F = 3.2 kN. Ignore stress concentration factors. See Section 4.9 in Norton for help with curved beams. MPa N O MAX |F F 60 mm 40 mm 12 mm 33 mm 33 mm Section A-A A
A 28 mm diameter rod with a 30 mm diameter handle as shown in Figure Q1 has two 90 degree bends. The handle is attached to the wall at 'A' while 1.8kN load is applied at the end of the rod at 'E'. Calculate Maximum Shear Stress at location 'A' and 'B' and determine it critical location. Bending load at point 'A'? Bending load at point 'B'? (Nm) Torsion load at rod; 'T'? Normal Stress due to bending load at point 'A'? (MPashear Stress due to torsion load at point 'A'? (MPa) 1st Principle stress at point 'A' (max principle stress)? (MPa Maximum shear stress at point 'B'? Critical Location? (L1) 170 $30- (L2) в 470 $28- F= 1.8kN| E 300 100 (L3) D Figure Q1
A shaft under the torsion has a pure shear stress on the surface. What is the maximum principal stress on the surface which is at 45° to the axis?