A hollow tube havingan 'inside dia metes of (3m)and a wll thick ness of (0:5mm) isexpased to anenviroment at (h = 100 wht-t) and (Too=40k Whetheat generation nate in the tube will producetube deuperatar f 250€ for kesowlm.ksurface is insulated.a maximumAssumetheinnerO whet are the kate7 heat.

Answered: Image /qna-images/answer/1d510608-4c5d-4671-93a8-1f86aef75c70.jpg

A hollow tube having on inside diametes of (3em) and a wall thickness of (0:5mm) isexpased to an enviroment at (hz 100 wh.e) and (Tooz4ok Whet heat generation nate in the tuke will produce 250e for ka3owln.k tube deuperatar f 250€ for ke30W/.k surface is insulated. amaximunt Assume he inner e whet are the kate heat.

A hollow tube having on inside diametes of (3em) and a wall thickness of (0:5mm) isexpased to an enviroment at (hz 100 wh.e) and (Tooz4ok Whet heat generation nate in the tuke will produce 250e for ka3owln.k tube deuperatar f 250€ for ke30W/.k surface is insulated. amaximunt Assume he inner e whet are the kate heat.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Building requires average 200kg of hot water at temperature 50 oC per day. Specific heat of water 4185.5 J kg-1K-1 or 1.1626 Wh kg- 1K-1. The solar collector system used to increase the temperature from 10 to 50 oC, the system has an efficiency 40%, assume yearly solar radiation is 1000 kWh/m2/year, desired solar fraction SF= 60%, The collector area is O a. 6m^2 O b. 5m^2 О с. Зт^2 O d. 2m^2 O e. All of the answers are not correct
A hollow tube having and a wall thick ness of (0:5mm) isexpased to an enviroment at (h= 100w/h-E) and (Too=40tWhet heat generation nate in the tube will produce an inside diia metes of (3cm) tabe temperatar the inner 250€ for kasowlinik a maximu m surface is insulatid. A heat. Assume O whet are the kate 2 Whet are
3.5 MPa 400 C 3MPA 500 E Heater Wout =6-5 MW (from Turblne It I) insulated Türbine insulated Turbine II Steam 9MPA 550 C 90 C -X=96 % steam (in kg/s) Find: O m of O & to the heater Cin kw).
if A 22 C Water enters a heat exchanger with a velocity 0.8 m/s and tube diameter is 10 mm, it leaves at 34 C what is the heat transferred to water. in kW 3.157 O 31.569 O 3.94 O
Thermodynamics. Please help me out A Carnot heat engine is used to power a Carnot refrigerator that operatesbetween 258.15 K and 293.15 K. In the heat engine, water is used as theworking fluid. Heat is added to the water at 473.15 K, where it changes fromsaturated liquid to saturated vapor. Heat is rejected from the heat engine atP=20 kPa and constant temperatue. Calculate(a) The heat added to the water per kilogram of water(b) The amount of heat that must be added to the water so that therefrigerator can remove 1 kJ of heat from the cold reservoir.
Let the cylinder (hollow) in the figure has variable heat generation which is
A refrigeration system is being designed to maintain a small frozen storage room at -5°C. The required cooling rate is 50 kW. Waste heat from the refrigeration system will be rejected to the outdoor air at 35°C. The system will be designed such that the evaporation temperature will be either -10°C or -20°C, and the condensing temperature will be either 40°C or 50°C. UA cond For the 4 possible combinations of evaporator and condenser Tcond temperatures: Apply the "rule of thumb" to estimate the cooling COP Tn Есотp Estimate the required "size" of the evaporator heat exchange Practical Refrig surface, UA vap (W/°C) Estimate the required "size" of the condenser heat exchange surface, UAcond (W/°C) Тevap UAevap Show your work for Scenario A and complete the following table: Design Scenario Tevap (°C) СОР. UA. UA cond (W/°C) Tcond (°C) (W/°C) evap A -10 40 В -20 40 -10 50 -20 50
A 95kg/hr hot fluid is used to heat a cold fluid from 10oC to 70oC using a double pipe heat exchanger (DPHE). The hot fluid enters at 205°C and leaves the DPHE at 108°C. The Cp of hot fluid is 1.10 kcal/kg°C and the Cp of cold fluid 0.95 kcal/kg°C. a) Calculate the LMTD if the the flow is cocurrent in oC b) Calculate the LMTD if the the flow is countercurrent in oC
exhausted steam at 7 kpa atb a rate of 75 kg/sec enter a single pass condenser containing 5780 pcs copper tube with a total area of 2950 m. the steam has a mositure content of 10 percentage and the condensate leaves satured liquid at asteam temperature. the cooling water flow rate is 4413 lit perb sec entering at 20C. size of tubes, 25 mm diameter by 3 mm thick wall. find the over all heat transfer coefficuent.
A computer lab filled with 20 computers and 15 students is cooled by an air conditioningunit on a day where it is 90 oF outside. The room temperature is 72 oF. Assume an averagestudent generate 90 W of heat and each computer generates 150 W of heat. If the COP ofthe air conditioner is 2.5, what power input is required, in kW? If the air conditioneroperated at its maximum coefficient of performance, what power input would be required?
The condenser of a large thermal power plant consists of a single body with two passes each and 30000 pipes.It is a shell and tube type heat exchanger. Pipes are 25 mm inner diameter, thin-walled and steam,11000 W / m2With a convection coefficient of .K, it condenses on the outer surfaces of the pipe. HeatThe transfer required by the exchanger is 2000 MW, and 30000 kg / h of water will be transferred from the pipes.as with flowing flow rate. Water enters at a temperature of 20 ° C, steam at 50 ° C.is condensing. Calculation temperature of the cooling water from the condenser? Required per passdetermine the pipe length? The properties of water at Tort = 300 K; Cp = 4180 j / kgK, μ = 855 × 10--6 Ns / m2,k = 0.613 W / mK, Pr = 5.83.