A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter, transmits 6000 hp at 200 rev/min. Use G=12x10 psi for steel. Calculate (a) the maximum shear stress; (b) the angle of twist of the shaft.

A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter, transmits 6000 hp at 200 rev/min. Use G=12x10 psi for steel. Calculate (a) the maximum shear stress; (b) the angle of twist of the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 /A/ In casting experiments performed using a certain alloy and type of sand mold, casting made of steel with shape as disk, with diameter =700mm and 30mm thickness , it took 20sec for a solidify Determine the value of the mold constant in Chvorinov's rule
The figure below is the basic plot of pressure vs. volume for the Dual Standard Cycle. Constant pressure heat addition 3 4 PV = constant %3D Heat IN Adiabatic expansion 2 Heat OUT (Constant volume heat rejection) Constant volume heat addition 1 Adiabatic compression Volume (V) Using the Dual Air Standard Cycle and the following data: • Assume constant properties of air. R= 287 J/kgK; Cp = 1005 J/kgK; Cv = 718 J/kgK; y = 1.4 • Cycle compression ratio = 14 (V1/v2) • Air conditions prior to compression: Pressure = 1.3 bar; Temperature = 293K • Heat added at constant volume = 280000 J/kg • Heat added at constant pressure = 662000 J/kg Pressure (P)
The product of molecular weight and specific gas constant is known as,
Solve fast
Q.B3. As part of a project, students have been asked to cast an Aluminium disc for use as a flywheel. The flywheel is part of an engine development project and needs to be 200 mm in diameter and 20 mm thick. Green sand casting will be used. The shrinkage associated with this metal and process is 5% at the solidification stage and further 3 % on cooling to room temperature. Aluminum has a density of 2710 kg/m³ and a melting temperature of 660°C. The pouring temperature is 700°C while the specific heat of aluminum is 887 J/kg.K. The latent heat of fusion of Aluminum is 396 kJ/kg. From previous experiments the Chorinov constant for the mold was found to be 10 s/mm². Determine: a.) The dimensions of the pattern (diameter and thickness) that will need to be made for this part (ignore riser and sprue). b.) The time it will take for complete solidification of the part. c.) Assuming an electric furnace at 10% efficiency is used to heat the metal and it takes around 2 hours achieve pouring…
On F2, how to identify the if we need to multiply it by "(4/5) and (3/5) slopes"?
With complete and clear units/conversion factors. Box your final answer and round to the nearest 2 decimal places. Thank you
The temperature of the body decreased from 200 to 100 in theroom for 60 minutes. if the room temperature is Ts, also the bodycooling decreased to 80 in 60 minutes more, Find Ts and the rate of change k?
Calculate the temperature at the end of the heat addition process.
Through the following formulas: (100-FGM) DP 100-IGM WGI= where: WGI - Wet grain input in ton/h DP-Dryer performance in ton/h FGM - Final grain moisture in % IGM - Initial grain moisture in % EP =WGI-DP where: EP - Evaporation power in ton+₂0/h EC = GC HP where: EC - Energy consumption in kcal/h GC-gasoil consumption in kg/h HP-heating power of gasoil in kcal/kg SEC where: SEC - Specific energy consumption in kcal/kgH20 Select which of the following specific energy consumption options correspond to a dryer that has a performance of 40 tons/h, and is required to reduce grain moisture from 17% to 13.5%. Data: EC EP-1000 heating power of gasoil-10100 kcal/kg gasoil consumption=213 kg/h Answer 500-1000 kcal/kg H20 1500-2000 kcal/kg H20 1000-1500 kcal/kg H20 O O O
101.3 kpa expands constant temperature from 0.l m' to 10 ft', what is the final pressure in bar
Q2 /A/ In casting experiments performed using a certain alloy and type of sand mold, casting made of steel with shape as disk, with diameter =700mm and 30mm thickness, it took 20sec for a solidify Determine the value of the mold constant in Chvorinov's rule