A hollow steel member has an inside diameter of 50mm,a wall thickness of 5mm,a length of 1500mm and a modulus of elasticity of 210GPa.if the member is subjected to a tensile load of 5KN, determine each of the following dimensional changes.(take Poisson's ratio to be 0.4) 1.elongation 2.change in thickness

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

A:

Q: Find the modulus of elasticity Stress=2 MPa Strain=0.1

A: Given data : Strain is denoted by ε Stress is denoted by σ   To find : Modulus of elasticity

Q: 2. A metal plate is .125 inch thick. What force is required to punch out a square piece 1" x 1"? Th…

A: Thickness of metal plate is 0.125 inch Size of square piece is 1''×1'' The ultimate shear stress of…

Q: A steel bar of 50 mm × 50 mm square cross-section is subjected to an axial compressive load 200 kN.…

A: Steel bar 50 mm x 50 mm, Axial compressive load P = 200 kN Length L = 2 m, E=160 GPa Deformation = ?

Q: A 2.0 m steel is being subjected into a tensile test. At force 30 kN, the length of the steel is now…

A: Given, Initial length of the steel subject (Li) = 2 m Length of steel after loading (LL) = 2.2 m…

Q: Find the value of strain if stress is 40 N/mm2 and Youngs modulus is 70 N/mm2

A: Given data : The value of stress σ=40 N/mm2 The value of Youngs modulus E=70 N/mm2   Required :…

Q: HAMMA A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05…

A:

Q: bar shown if the temperature increas supports are unyielding and that the buckling. 4 Aluminum A =…

A:

Q: Diameter of the metal bar, before and after load application was measured to be 100.00 mm and 99.99…

A:

Q: The composite shaft shown in the figure is manufactured by shrink-fitting a steel sleeve over a…

A: the shown composite shaft shown in figure is formed by shrink and fitting in which it is given outer…

Q: 30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected…

A: we have to determine the lateral strain

Q: } 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a…

A:

Q: In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is…

A:

Q: The strain gauge measurement of a steel plate indicate the principle strains are 0.003 and 0.001.…

A: Principle strains- ε1=0.003ε2=0.001E=200 GPaμ=0.33

Q: A steel column has a sectional area of 0.126 m^2 and a length of 3 m. IF a 50000 KN load is applied…

A:

Q: 3. An aluminum bar having a cross-sectional area of 0.25 sq. in. carries the axial loads applied at…

A:

Q: Find the modulus of elasticity Stress=2 MPa

A: According to given data  Stress = 2 MPaStrain = 0.1

Q: condition of plane stress are: of the principal stresses in the

A:

Q: Problem- wwwwwwwww A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load…

A: Given- Steel bar length L=2 m=2000 mm, Width b=20 mm, Thickness t=15 mm, Tensile load P=30 kN,…

Q: Assume if the shear stress in steel exceeds about 4.00 x 10^8 N/m2 the steel ruptures. (a) Determine…

A: Given : Allowable shear stress = 4 X 108 N/m2 Diameter of steel bolt = 1.05 cm Diameter of hole =…

Q: Determine the value of strain if modulus of elasticity is 70 MPa and stress is 20 MPa

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

A: Given data- Tension stress-σy=280 N/mm2σ1=122 N/mm2 (tensile)σ2=60 N/mm2 (compressive)poisson's…

Q: Find the value of strain if stress is 45 Mpa and modulus of elasticity 70 MPa

A:

Q: The strain in member AB was measured to be 9 × 10^−4. If the member is an ? 3 × 3 × 1/4 of A36 steel…

A:

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

A:

Q: Which of the following is a deformation? Select one: a. Tension b. Shear c. Compression d. Strain

A:

Q: 600 480 600 480 360 360 240 240 120 120 0.000 0.006 0.002 0.004 Strain 00 0.04 0.08 0.12 0.16 0.20…

A:

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Q: Determine the Poisson's ratio v.

A:

Q: A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If…

A:

Q: An aluminum tube has an outside diameter of 2.5 inches will be used to support 27 kips of load. If…

A: Determine thickness,t=?

Q: A tensile force P Newton is applied gradually on a prismatic bar of length L m and areas of cross-…

A: Tensile force=P N Length=L Area=A

Q: Determine stress value

A: This question is related with solid mechanics . In this question we are provided with value of…

Q: A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05 mm…

A: Given data- Length L=100 mm,change in length ∆L=0.05 mm,E=200 GPa, To Find- The value of stress…

Planar Stresses