A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a diameter of 80 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 81 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? P High-density polyethelene (HDPE) rod Answer: i P kN

A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a diameter of 80 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 81 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? P High-density polyethelene (HDPE) rod Answer: i P kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4) The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 250 N is applied to it, determine the change in its length and the change in its diameter. Assume the elastic modulus, E, is 2.24 GPa, and the shear modulus, G, is 870 MPa. 250 N 200 mm 250 N
The following terms apply to LRFD (limit state design) and ASD. Which of the following is a limit state design concept?
Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch radius hole centered on its width, as shown in the sketch. With an axial load, P = 8650 lbs applied, the maximum axial stress at the edges of the hole was experimentally determined to be 7670 psi What is the stress concentration factor, K, of the hole? 1.33 0.75 1.66 1.50 P 2.50 in. -Radius 1/4 in. P= 8650 lbs
If the lateral compressive strain in a material is 0.3 x 10-3 and the Poisson ratio is 0.25, then longitudinal strain in the material is ✓ 0.0012 (tensile) 0.0012 (compressive) 7.5 x 10-5 (compressive) 7.5 x 10-5 (tensile)
Round off final ans, dont round off initial values
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
The point loads are placed at the fixed positions shown in the figure and they are live loads. A k a b a b dn = 1₂ Icr= M B 7 Ast Stress profile (concrete) Cross section before cracking Aso Cross section Asc Ast N.A. Q2) Now, the live load increases gradually and the moment at the critical section just exceeds the cracking moment (Mcr), but the compressive section of the concrete is still under the linear elastic region. Please be reminded that in the flexural design, the crack of the concrete section starts where the tensile stress reaches the tensile strength. It is assumed that the cracks then propagate rapidly up to the entire tension section (up to the neutral axis) and this cracked concrete section cannot resist the tension. It should be noted that in reality, concrete sections between the primary cracks can still resist some tensile stresses as shown in the figure, which should be considered in the displacement design. However, in flexure design, we design the critical section…
A storage tank of air, 30 inches in diameter, is to withstand an internal pressure of 180 psi with a design factor of 3.5 based on ultimate stress. The steel has the strength equivalent of C1020 annealed and the welded joints should have a relative strength of 92%. Note: ultimate stress of for annealed C1020 steel is 50 ksi. Compute for longitudinal stress of the tank. a.13, 171 psi b.13, 786 psi c.12,893 psi d.12,860 psi
A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a diameter of 100 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 102 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? P. High-density polyethelene (HDPE) rod Answer: P = i P kN
i need the answer quickly
Present detailed drawings/FBD’s illustrating your solution.
Question.