A helical spring with a load range of from 450 N to 800 N from valve-closed to valve-open conditions is used to close the valve of a spring-set relief valve having a lift of 10 mm. Assuming the spring wire to be of chrome vanadium steel, the spring is rendering average service, determine the diameter of the wire if the spring index is 7 and Sg - 420 MPa. Use G=83GPA. Select one: O a. 2.4-mm wire

A helical spring with a load range of from 450 N to 800 N from valve-closed to valve-open conditions is used to close the valve of a spring-set relief valve having a lift of 10 mm. Assuming the spring wire to be of chrome vanadium steel, the spring is rendering average service, determine the diameter of the wire if the spring index is 7 and Sg - 420 MPa. Use G=83GPA. Select one: O a. 2.4-mm wire

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, is subjected to a load which varies from 416 N to 950 N. The spring index is 6.7 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa,find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm2.
Problem 3: Design a helical compression spring to be used to return a pneumatic cylinder to its original position after being actuated. At a length of 10.50 in, the spring must exert a force of 60 lb. At a length of 4.00 in, it must exert a force of 250 Ib. Severe service is expected. Use ASTM A231 steel wire.
. A helical compression spring is to be made of oil-tempered wire of 4 mm diameter with a spring index of C=10. The spring is to operate inside a hole, so buckling is not a problem, and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (Take: G= 77 GPa) 1- Determine the minimum hole diameter for the spring to operate in. 2-Determine the solid length. 3-Determine a static factor of safety based on the yielding of the spring if it is compressed to its solid length.
PROBLEM:2 A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter of 12.5 mm and 15 active coils. Find (a) Stiffness of the spring (b) solid length. Assume that the ends are squared and ground. Take modulus of rigidity as 0.85x105 N/mm2.
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 18 degree Celsius, 2 m 2 m A 2 m Use E= 200 GPa linear of coefficient expansion = 117x10 per degree celsius and A=4500 mmt Compute the force in the right rod. Select the correct response. -151 63 kN -101 09 kN
Problem A 1) Find the equivalent spring,N/mm 2) Find the force, F KI K5 k k K2 x=10 mim k 00000 0000 k КЗ K4 K6 ....... ...... ...... ...... ........... .. ........
None
Don't try if you don't know. I need full explanation
Please help with all thank you!!
- In a compound helical spring, the inner spring is arranged within and concentric outer one but is 10 min shorter. The outer spring has 10 coils of mean diaineter 30 min and wire dia 3 mm. Find stiffness of inner spring if an axial load of 100 N causes outer one to compress by 20 mm. If the radial clearance between the springs is 2 mm, find wire diameter of inner spring which has 8 coild. G 80 kN/mm.
A helical compression spring has a scale of 400 lb/inch, an inside diameter of 2.5 inches, a free length of 8 inches and with squared and ground ends. Material is to be chrome vanadium steel. For a load, P, of 750 pounds, and for average service, determine the solid height. Working stress is 63 ksi, G = 10,800 ksi.
A helical compression spring with squared and ground ends has an outside diameter of 1.100 in, a wire diameter of 0.085 in, and a solid height of 0.563 in.Compute the ID, the mean diameter, the spring index, and the approximate number of coils.