A helical spring having squared and ground ends has active of 16 coils and its material has modulus of elasticity in shear of 78.910 Gpa. If the spring has an outside diameter of 10.42 cm and a wire diameter of 0.625 cm, compute the deflection in the spring due to a load of 50 kgs. A. 302 mm B. 490 mm C. 400 mm D. 322 mm

A helical spring having squared and ground ends has active of 16 coils and its material has modulus of elasticity in shear of 78.910 Gpa. If the spring has an outside diameter of 10.42 cm and a wire diameter of 0.625 cm, compute the deflection in the spring due to a load of 50 kgs. A. 302 mm B. 490 mm C. 400 mm D. 322 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE ANSWER QUICKLY
Big and clear handwriting with all the steps. Make sure calculations and answers are accurate please. THANK YOU
Research and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Explain how this tolerance is defined
A siilicon boule has been processed through grinding to provide a cylinder whose diameter = 281 mm and whose length = 899 mm. Next, it will be sliced into wafers 0.8 mm thick using a cut-off saw with a kerf = 0.5 mm. The wafer thus produced will be used to fabricate as many IC chips as possible for the personal computer market. Each IC has a market value to the company of $108. Each chip is square with 17 mm on a side. The processable area of each wafer is defined by a diameter = 265 mm. Estimate the value of all of the IC chips that could be produced (in $), asssuming an overall yield of 84% good product.
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
Solve it quickly please
A bimetallic strip (brass/steel), which is straight at room temperature, will be immersed in boiling water and allowed to equilibrate. I will then remove the strip and quickly place it on a piece of graph paper to measure the deflection of the end, i.e. how far the end is away from the original line, measured perpendicular to the original line. Predict how far the end will deflect, to the nearest half millimeter. The bimetallic strip is 222 mm long. I measured the thickness to be 0.036". You may inspect the room- temperature strip and check my measurements. Snipping Tool If u don't know concept of whole question|please skip it otherwise I give u 10 downvotes I need step by step solution remember this thing
The new line of go-karts will have a two-stroke internal combustion engine. The engine generates 35 horsepower at a mean speed of 2000 rpm. The biggest variation in energy per revolution, according to dynamic analysis, is 25% of the mean energy. Design a flywheel to go along with this engine such that the maximum coefficient of speed fluctuation is 0.01. Your design should include all necessary details, such as the design calculations, the appropriate material, detailed dimensions, and manufacturing procedures. Note: As a design problem, there is more than one acceptable solution. One design, though, might be superior to others.
can you please find solution for this question
A stringer of tennis rackets has found that the actual string tension achieved for any individual racket will vary as much as 6 pounds per square inch from the desired tension set on the stringing machine. If the stringer wishes to string at a tension lower than that specified by a customer only 5% of the time, how much above or below the customer's specified tension should the string set the stringer machine
Help me please
The figure shows a wooden model to reproduce a metal piece ofaluminum through the sand casting process.a) How much mass (g or kg) of aluminum do you need to melt?b) How much energy Q (Joules) is required? Assume an initial temperature of 50 ° C and a100% thermal efficiency.c) What dimensions will the final metal piece have? all is in cm