A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=D0.154-0.912/T, where T, represents the equivalent num- ber of teeth. The velocity factor is given by C, = 6 + v where v is the peripheral speed of the gear in m/s.

A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=D0.154-0.912/T, where T, represents the equivalent num- ber of teeth. The velocity factor is given by C, = 6 + v where v is the peripheral speed of the gear in m/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A 20 degree pressure angle spur gear set is transmitting 10 horsepower at 1,000 RPM. The pinion has…

A: The pressure angle = 20 degrees The horsepower, P = 10 hp the speed of the gear, N = 1000 rpm The…

Q: A gear-reduction unit uses the countershaft depicted in Figure 4. Q6: shaft is 420 MPa. Determine…

A: Assuming no power losses through the shaftTA.ω-TB.ωTA=TB5cos20°2402=Fcos25°1002F=10.368 KNCalculate…

Q: Q 09. Consider a pair of 30° full depth involute spur gears having 20 and 40 teeth respectively and…

A: Find the addendum of smaller gear.

Q: A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion…

A: For the given yield stress and materials,Consider the velocity factor and service factor to be, .

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-tooth…

A: Given, Pressure angle,ϕ=20°N=1800rpmPower,P=4hp=4×746=2984WNumber of teeth of pinion,Tp=17Number of…

Q: A straight bevel gear pair has the following data: Np = 25; NG = 50: P = 10; 20° pressure angle. If…

A: given; number of teeth of gear (TG)=50number of teeth of pinion (Tp)=25speed of…

Q: If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of…

A: If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of…

Q: What is the transmitted load exerted by the pinion on the gear? Report your answer in lbf.

A: Given:Pinion Np=17 teeth, Gear Ng=52 teeth, Pressure angle∅=20∘ Power H=4 hp Diametral pitch Pd=10…

Q: A pair of straight bevel gears drives the vertical drilling machine. The approximate speed reduction…

Q: A planetary gear used on the Mars rover uses a 25-tooth helical gear with ψ = 20° has a 25° pressure…

A: Given Data The number of tooth are: N=25 The angle of the thread is: ψ=20° The pressure angle is:…

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-tooth…

Q: A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure…

Q: What is the total force exerted by the pinion on the gear? Report your answer in lbf.

Q: the tip of the inner cone is the location of the maximum temperature in a neutral oxyacetylene…

A: Solution: The Correct Option with necessary explanation is given below:

Q: A speed reduction gear box consist of an SAE 4140 steel pinion mounted to a shaft on a 30 HP, 1750…

Q: A steel spur pinion has a pitch of 6 teeth/in, 22 tooth full-depth teeth with a cut profile, and a…

Q: A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000 rpm. The gears…

Q: An epicyclic reduction gear shown in figure, has a shaft A fixed to arm. The arm has a pin fixed to…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

A helical cast steel gear with 30° helix angle has to transmit 35
kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary
module, pitch diameters and face width for 20° full depth
involute teeth. The static stress for cast steel may be taken as
100 MPa. The face width may be taken as 3 times the normal
pitch. The tooth form factor is given by the expression
y'=0.154 – 0.912/T, where T represents the equivalent num-
ber of teeth. The velocity factor is given by C, =
6 + v
where
v is the peripheral speed of the gear in m/s.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the radial load exerted by the pinion on the gear? Report your answer in lbf.
8
find the shaft diameter and the factor of safety against yielding those numbers arent correct
1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r /min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Z1 = 26. The allowable stress and factors for material %3D is: [0]= 600 MPa, [o„]z= 599 MPa, [0,]ı= 220 MPa, [0,]= 213 MPa. E=1.693, Z, =1898/mpa Z„ = 2.5 K =1.25 Ky =1.1 K K =1.2 На K =1.35 Y =2.65, Y = 2.28 Y =1.58 Y =1.76 %3D Fa2 Fal sa1
Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
There are two pairs of closed soft tooth surface spur gears A and B,Parameters of A: modulus m = 2mm, number of teeth Z1 = 40, Z2 = 90 , width of teeth b = 60mm.Parameters of B : modulus m = 4mm, number of teeth Z1 = 20, Z2 = 45 , width of teeth b = 60mm.The accuracy of the two pairs of gears is grade8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason.
p sa 15. A straight bevel gear pair has the following data: 50; P¿ 10; and 20° pressure angle. If the gear pair is transmitting 3.5 hp, compute the fore- es on both the pinion and the gear. The pinion speed is 1250 rpm. The face width is 0.70 in. Compute the bend- ing stress and the contact stress for the teeth, and specify a suitable material and heat treatment. The gears are driven by a gasoline engine, and the load is a conveyor provid- ing moderate shock. Assume that neither gear is straddle nounted. N₂ No = 25; No J (M
A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
A helical gear has a normal diametral pitch of 12. a nor- mal pressure angle of 20°, 48 teeth. a face width of 1.50 in, and a helix angle of 45°. (a) If the gear transmits 2.50 hp at a speed of 1750 rpm., compute the tangential force, the axial force, and the radial force. (b) If the gear operates with a pinion having 16 teeth. compute the bending stress in the pinion teeth. The power comes from an electric motor, and the drive is to a centrifugal blower. Specify a quality number for the teeth. (c) Specify a suitable material for the pinion and the gear considering both strength and pitting resistance.