A heat pump operates on the ideal vapor-compression refrigeration cycle and uses refrigerant-134a as the working fluid. The condenser operates at 1400 kPa and the evaporator at 140 kPa. Determine this system's COP and the rate of heat supplied to the evaporator when the compressor consumes 7 kW. (Take the required values from saturated refrigerant-134a tables.) The COP of the system is and the rate of heat supplied to the evaporator is kW.

A heat pump operates on the ideal vapor-compression refrigeration cycle and uses refrigerant-134a as the working fluid. The condenser operates at 1400 kPa and the evaporator at 140 kPa. Determine this system's COP and the rate of heat supplied to the evaporator when the compressor consumes 7 kW. (Take the required values from saturated refrigerant-134a tables.) The COP of the system is and the rate of heat supplied to the evaporator is kW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cooling system with a capacity of 10 tons of refrigeration operates at 210 KPA in the evaporator while in the condenser it is 850 KPA if the R-134a refrigerant is in a saturated state calculate the theoretical power required to operate the compressor.
750 kPa 800 kPa 55°C Condenser (3) Expansion valve Compressor Evaporator Figure 3 4. The liquid leaving the condenser of a 30 kW heat pump using refrigerant 134a as the working fluid is subcooled by 5.4°C. The condenser operates at 1 MPa and the evaporator at 0.4 MPa. How does this subcooling change the power required to drive the compressor as compared to an ideal vapour-compression refrigeration cycle? (3.41 kW, 3.25 kW)
Saturated vapor R22 refrigerant leaves the evaporator and enters the compressor at 131.68kPa. The refrigerant leaves the condenser as a saturated liquid at 40oC and enters theexpansion valve at 36oC. Heat rejected from the condenser amount to 105 kW. The work tothe compressor is 65 kJ/kg, while the heat loss from the compressor is 5.5 kJ/kg. A 7.4 kJkgof heat loss in piping between the compressor and condenser, Draw the p-h diagram(labeling the pressures and temperatures in each condition). Determine (a) the temperatureof refrigerant entering the condenser and (b) calculate the refrigeration capacity in tons.
A two-evaporatoor compression refrigeration system like that in the Figure below uses refrigerant-134a as the working fluid. The system operates evaporator 1 at 30 psia, evaporator 2 at 10 psia, and the condeser at 180 psia. The cooling load for evaporator 1 is 9000 Btu/h and that for evaporator 2 is 24,000 Btu/h. Determine the power required to operate the compressor and the COP of this system. The regrigerant is saturated liquid at the exit of the condenser and saturated vapor at the exit of each evaporator, and the compressor is isentropic.
ai 10roh Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.2 MPa and 200 kPa with refrigerant-134a as the working fluid. The refrigerant leaves the condenser as a saturated liquid and is throttled to a flash chamber operating at 0.32 MPa. Part of the refrigerant evaporates during this flashing process, and this vapor is mixed with the refrigerant leaving the low-pressure compressor. The mixture is then compressed to the condenser pressure by the high-pressure compressor. The liquid in the flash chamber is throttled to the evaporator pressure and cools the refrigerated space as it vaporizes in the evaporator. The mass flow rate of the refrigerant through the low-pressure compressor is 0.11 kg/s. Assuming the refrigerant leaves the evaporator as a saturated vapor and the isentropic efficiency is 85 percent for both compressors, determine (a) the mass flow rate of the refrigerant through the high-pressure compressor, (b) the rate of heat removal…
An ammonia refrigerating system has a load of 250 kW and operates at a condensing pressure of 1400 kPa and an evaporating temperature of -20°C. The refrigerant exits at the evaporator with a 5- degree superheat. The vapor enters the compressor suction at 10-degree superheat. The compressed vapor is discharged from the compressor at the condensing pressure and 150°C. The refrigerant exits the condenser as saturated liquid. a. State the enthalpies at each point: Point enthalpy kJ/kg h kJ/kg kJ/kg h2 kJ/kg h3 kJ/kg h4 Answer: kg/sec b. Calculate the mass flow of refrigerant Answer: kW C. Determine the size of the motor drive if the mechanical efficiency of the motor- compressor is 77%. Answer: kW Calculate the total heat rejected in the condenser. d. Determine the refrigerating efficiency of the system. Answer: е.
Determine the cooling capacity and the coefficient of performance of the air conditioning system?
A vapor-compression system produces 20 tons of refrigeration using R12 as a refrigerant while operating between a condenser temperature of 41.6°c and an evaporator temperature of – 25°c. The superheat at the compression suction and the sub-cooling at the condenser outlet are 10°K. The pressure drop are 10kPa across the evaporator and the condenser. Determine the refrigerating effect in kJ per kilogram, the circulating rate of R12 in kilograms per second, the power required, the COP, the heat rejected in kW and the volume flow rate of refrigerant at compressor inlet conditions. 10° K subcooling 4 Tm= 41.6° C h= C s =C Tevap =-25° C 10° K superheat
A refrigeration system with a capacity of 15 tons of refrigeration, operates at 150 kPa in the evaporator, while in the condenser it is 1000 kPa. If R-134a refrigerant is in a saturated state, calculate the theoretical power required to operate the compressor. Compressor Power