A half wave rectifier is given below as shown. The load is a resistive type of 25 Q. The source is an ac type of 60 Hz and the rms value is given as 110 v. (a) (a) Calculate the average output voltage vo and the average output current io. (b) Find the rms output voltage and rms output current. (c) What would be the average power being delivered to the resistive load. (d) If the input ac source has an input resistance equals to 20, then what part of average power will be transferred to the load side? (e) Find the efficiency of the above half wave rectifier in case of part (c) and part (d).

A half wave rectifier is given below as shown. The load is a resistive type of 25 Q. The source is an ac type of 60 Hz and the rms value is given as 110 v. (a) (a) Calculate the average output voltage vo and the average output current io. (b) Find the rms output voltage and rms output current. (c) What would be the average power being delivered to the resistive load. (d) If the input ac source has an input resistance equals to 20, then what part of average power will be transferred to the load side? (e) Find the efficiency of the above half wave rectifier in case of part (c) and part (d).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

N H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr 150usec and the source voltage Vs = 200V at frequency = 5 kHz. Calculate the average output voltage. IC L.C. the HoNo locor
Question 2) A full-wave rectifier with ohmic load given in the figure below feeds a 75 Q load and the effective (rms) value of the source voltage is 220V, its frequency is 50 Hz. Accordingly, find the following desired circuit parameters: a) the peak voltage of the source, b) the peak current of the load, c) Average stress of the load, d) Average current of the load, e) The effective (rms) voltage of the load, f) Effective (rms) current of the load, g) Power of the load i D2 vs R
Q-2: The input signal for half-wave rectifier is a.c. signal. The output of 800 load resistor is 50V d.c. voltage. The diode has a resistance of 25 Q. 5 a) Draw the graphs of input signal, diode signal and output signals. 20 b) Calculate the maximum voltage value for the input signal. AC Supply Diode www
The input to a full-wave rectifier is 10 V AC (RMS). The load resistor is 10 ohms. The DC voltage at the output is:
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
A Single Phase Half Wave Controlled Rectifier has a DC voltage of 20V and a source voltage of 100Vpk. If it supplies a resistive load of 1 ohm. Find its output voltage and current in RMS.
9. The diodes in a bridge rectifier each have a maximum dc current rating of 2 A. What is the maximum value of the dc load current? 10. What is the PIV across each diode of a bridge rectifier with a secondary voltage of 20 V,rms?
A full-wave rectifier uses two diodes. The transformer r.m.s. secondary voltage from the center tap to each end of the secondary is 70 V and load resistance is 1000 0. Find: a) The mean load voltage and current b) The r.m.s. value of load current e) The PIV of the diode d) The efficiency of rectification
PROBLEM SET 1. Derive the formula for the RMS value for the following a) b) 3m 2. Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. 3. Following the analysis applied to the half-wave rectifier with capacitor filter, show how to arrive at the output waveform for a center-tapped full-wave with filter capacitor. See output waveform on page 90. 4. Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 µF; average load voltage 18 V. Determine ripple factor and average load current 5. Design a half-wave rectifier with a capacitor filter that will deliver to the load an average voltage is 15 V at 280 mA. Ripple should not be higher than 5%. 6. Given: The input to a voltage regulator circuit varies from 11.4 to 12.2 V. The load voltage is to be maintained at 9.1V with maximum…
What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (236 v), and true form foctor of input waveform is (114). *
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110V/11-0-11 V is used with R₁ = 1 KQ. Assume diode as Germanium. D₁ a) Find Input Voltage Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. •ooooo 00000 CT 20-S D₂ R₁
In a single phase full wave controlled rectifier connected to Inductive load (with freewheeling diode) find the expression for the average value of voltage across the load when supply voltage is Vs = Vm sinwt and firing angle = a. Vm/TT cosa 2Vm/TT cosa Vm/TT (1+cosa) 2Vm/TT (1+cosa)