a h 2. S Z- C h 2

Q: 7.4-10 through 7.4-15 An element in plane stress is subjected to stresses o,, o,, and Using Mohr's…

A: Given: The normal stresses are, The shear stress is, The angle is,

Q: A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15…

A: Given data:- V=15 Kips =15×103 lb L=6 =6×12=72 inP=10 Kips=10×103 lb   In the given section W12X35…

Q: Determine the maximum tensile and compressive bending stresses developed in the beam shown. The…

A:

Q: 9-14. The state of stress at a point is shown on the element. Determine (a) the principal stress and…

A:

Q: For the element shown in figure. Calculate 1) Principle sthesses 2) Maximum in-plane shear stress 3)…

A:

Q: The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress…

A: Option 4 is the correct

Q: A plate is connected to another plate via 20 mm diameter rivets. It carries a load of P=155 kN at a…

A:

Q: PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid…

A:

Q: As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a…

A:

Q: As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm…

A: Consider the free body diagram

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips -d2 =1.5" !0 kips 20 kips d, =3" A Fig. for Problem #2

A: There are 3 bars AB, BC, CDThe forces on those bars are also given.Diameter of bar CD, d1 = 2…

Q: An element in plane stress is subjected to stresses o , o , and 7 y (see figure). Using Mohr's…

A:

Q: Required information Consider the given state of stress. 416 ksi 10 ksi ormino the normal and…

A: The given data is: σx=0 ksiσy=16 ksiζxy=10 ksiθ=15°2θ=30°

Q: To lower ends of the three bars in the figure two are the same level before the rigid homogeneous…

A: In the question given above, Total weight of the blockW =176 knThus , Ps +Ps+Pb=176 knAs the loading…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A:

Q: Try to write out the stress boundary conditions of the cantilever beam. ( not include the fixed…

A: Three force are there on cantilever beam   F force, UVL load and q force.....

Q: a. Use Castigliano's Theorem and determine the vertical displacement of point C. Each steel has…

A:

Q: For the beam shown below, the ratio of stiffness coefficients k41 and K43 is Assume El is constant.…

A: For the given beam,To find the ratio of stiffness  coefficient

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: Hi! Thank you for the question. As per the honor code, we’ll answer the first question since the…

Q: 8 kN 4 m 15 kN 5 kN 2 m 2 kN 2m 2m A B с D E The aluminum rod shown has a diameter of 20 mm and is…

A: Given: diameter, D = 20 mm E = 70 GPa

Q: The two bars are made of polystyrene, which has the stress-strain diagram shown. If the…

A: Given : Cross sectional area of bar AB is = 975 mm2 Cross Sectional area of bar BC = 2600 mm2…

Q: The T section shown below is the cross section of a beam form by joining two rectangular pieces of…

A:

Q: Abronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

A:

Q: 50 MPa 35 MPa B 30° 90 MPa The state of stress at a point in a member is shown on the element. You…

A:

Q: A horizontal beam AD is supported by an inclined strut BC carries a load W = 2.4KN at the position…

A:

Q: 3. emer to punch out thin plate objects of different shapes. The cross-section of the punch and die…

A:

Q: Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole…

A: bending stress=MmaxIyt I= 100× 106 mm4 Yt= 200mm Mmax=6P =6×19=114 kNm( hogging) Hence will cause…

Q: Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For…

A:

Q: The state of stress at a point in a member is shown on the element. Determine the principal normal…

A: Px = 30 MPa Py = -30MPa q = 40 MPa

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40…

A: Given Data:Tensile stressft=40MpaCompressive stress fc= 80MpaINA= 20×106mm4

Q: Determine the maximum magnitude of load P that can be applied to the truss. The maximum allowable…

A: Given : (Fr)max = 5.2 kN (Fc)max = 3 kN d = 2m Determine the max. magnitude load P that can be…

Q: From the beam shown, fc' = 28 MPa, fy = 414 MPa, βh = 1.20, Cc = 40 mm. Take D = 25 mm diameter…

A: D = 25mm

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.