7.4-10 through 7.4-15 An element in plane stress is subjected to stresses o,, o,, and Using Mohr's cirele, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an element oriented at the angle 0. (Note: The angle 0 is positive when counterclock- wise and negative when clockwise.) 7,, (see figure). PROBS. 7.4-10 through 7.4-15 7.4-10 o, = 14 MPa, 7,=6 MPa, - 40° 27 MPa, o 140"

7.4-10 through 7.4-15 An element in plane stress is subjected to stresses o,, o,, and Using Mohr's cirele, determine the stresses acting on an element oriented at an angle 0 from the x axis. Show these stresses on a sketch of an element oriented at the angle 0. (Note: The angle 0 is positive when counterclock- wise and negative when clockwise.) 7,, (see figure). PROBS. 7.4-10 through 7.4-15 7.4-10 o, = 14 MPa, 7,=6 MPa, - 40° 27 MPa, o 140"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: QUESTION 3 For the beam show in figure 2, determine: (a) The reaction at the supports in term of the…

A: Given data P = 6 kn w=2kn/m

Q: The bars AB, CD and EF made of material with E=180 GPa and have a cross sectional area of 678 mm2.…

A: P=163N A=678mm2 E=180GPa

Q: For the structure loaded as shown below, derive the expressions that give: a) The horizontal…

A: Solution: Considering the diagram:

Q: In (Eigure 1), take that uy = 2.5 kN/m. igure 3 m- Wo 1.5 m 1 of 1 > ▼ Part A Replace the…

Q: 2. A finite element analysis of a bearing housing indicates that at a point p, the material is…

A: Principle stresses are the those stresses that are to the normal with zero plane. The value of…

Q: -termine the principal stresses, the maximum in plane d average normal stress. Specify the…

A: Since this a multiple question as per Bartleby policy, we can answer only first question, for other…

Q: 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

Q: The state of stress at a point is given by 0=x²y² + 30, 0₁y = x² + y² + 15. o = xy²2 + 30, T₁y =…

A: First we summarise the given data : To find : Determine the body force distribution at the point (…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are…

Q: 5- The solid rod is subjected to the loading suown. Determine the state of stress at point A, and…

A: Given : Determine the state of stress at point A and show the results on a differential volume…

Q: For the element shown in figure. Calculate 1) Principle sthesses 2) Maximum in-plane shear stress 3)…

Q: 2) Find... a) The principal planes b) The principal stresses c) The stress components exerted on the…

A: Givenσx=100Mpaσy=60Mpaτxy=-48MpaRadius of the circleR=(σx-σy2)2+τxy2R=(100-602)2+-482R=52…

Q: 1. Take the micro-body from the self-loading member, and bear the stress on it as shown in Figure a.…

A: Apply equilibrium of wedge

Q: 11 Strength is a physical property.( 12 True 13 False To be safe, strength of material is less th an…

A: Given that:- 11) Strength is a physical property As we know that size, state of matter, colour,…

Q: The state of plane strain on the element is P x = -300(10-6), P y = 0, and gxy = 150(10-6).…

A: (a) The x component of the strain is ϵx = -300 x 10-6 The y component of the strain is ϵx = 0 The…

Q: Consider a tetrahedron containing point Q and show the forces on the faces of the tetrahedron due to…

A: we consider a small element at point P whose shape is that of a tetrahedron. The three sides of the…

Q: El is constant, find the reaction forces. Using the method of consistent deformations

A: Calculation of Reactions at Supports using method of consistent deformation or Force method of…

Q: Problem 4 : For the shown Mohr circle: a) What is the state of stress at the reference point A.…

Q: nt is shown on the

A: given:σx=102MPaτxx=124MPa

Q: Obtain the maximum bending moment Mx that the cross section given below can safely carry. The…

A: Sigma=100MPa

Q: The state of strain at the point on the member has components of Px = 180(10-6), P y = -120(10-6),…

A: The given figure is shown below:

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A: Given data - Normal stress ,σx = 120 MPaσy = 60 MPa Shear stress ,τxy = 30 MPa Find - Principal…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: When force P is applied to the rigid arm ABC, point B displaces vertically downward through a…

A: To find the normal strain in wire CD, we need to determine the elongation of wire CD caused by the…

Q: a)Determine the change in temperature. Indicate increase or decrease in temperature. b)Determine…

Q: 80.7 MPa В. = 71.15" = -18.85 32.7 MPa 77.5 MPа C. = 67.91* -22.09* 25.5 MPa 84.7 MPa D. = 75.11"

Q: 160 MPа 160 MPа, The state of stress at a point is shown on the element. You are required to…

Q: W A L A Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end…

A: The objective of the question is to calculate the location of the centroid, the second moments and…

Q: Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods DE and a pin support at…

A: Draw free body diagram From deflected shape δAB8=δP4=δDE6=tanθ Consider the moment equilibrium…

Q: 2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in…

Q: An element in plane stress is subjected to stresses o, = -52.7 MPa and Txy = 41 MPa (see figure). It…

A: The stress element is shown in the figure.

Q: ) The stresses shown act at a point in a structural member. By equilibrium method, determine the…

Q: Poisson's ratio is a ratio of

A: Poisson ratio is denoted by μ When a load body deform under direction of load . The strain produced…

Q: a) Draw the Mohr's Circle associated with its original state of stress. Calculate and label the…

A: Assume The tensile stress as (+)ive The clockwise nature of shear stress as (+)ive. To…

Q: P2. The thin-walled cantilever beam of unsymmetrical cross-section supports shear loads at its free…

A: Given: Required Stress at point A at wall

Q: 2) The rigid bar ABC is horizontal before the load Pis applied as shown in the figure. Determine the…

Q: Problem 2 4 1 2 in 3 2 3 in 100 psi (a) Compute the unknown nodal displacements. (b) Compute the…

A: A beam element under axial load. The following information is given:Thickness (t) = 0.5 inE = psi…

Q: Determine the state of stress on the The state of stress at a critical section is shown in Fig.…

A: Given : This is a problem of solid mechanics where we have to find the state of stress on the…

Q: Stresses at any point in a simple axial member do not depend on the orientation of the plane being…

A: False The stress at a point in a body subjected to axial force depend on the inclination of the…

Q: Q: For the state of stress shown in fig. below. Determine the principle stress and the max. shearing…

A: To find principle stress and maximum shear stress

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

100%

7.4-10 through 7.4-15 An element in plane stress is
subjected to stresses o,, o,, and
Using Mohr's cirele, determine the stresses acting on
an element oriented at an angle 0 from the x axis. Show
these stresses on a sketch of an element oriented at the
angle 0. (Note: The angle 0 is positive when counterclock-
wise and negative when clockwise.)
7,, (see figure).
PROBS. 7.4-10 through 7.4-15
7.4-10
o, = 14 MPa, 7,=6 MPa, - 40°
27 MPa, o
140"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 21 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q-5: For the element with stresses as shown below, find: a. The magnitudes and directions of major and minor principal stresses b. The shear and normal stresses acting on a horizontal plane as shown below 8kPa 2kPa 75° 75° экра TH Jon OH 4kPa 30° Horizontal plane
Find OF g, C, I, A', ğ,b the value A' = area above = the distance from the center oF A to the centroidal axis moment Iner tia OF base the centroidal axis OF are a above attached tロ C = the distance From tne center to the topmost Fiber OF the bcam Formulas: Fb= Mc エ Ib Fb=bending stress v: shearing stress M = ma x value OF moment OF shear : E ay AT o. 0amm O.004mm 0.02mm 0.12 m m
Solve the required values using Mohr's Circle
B8
Required information Consider the given state of stress. Take A= 16 MPa and B= 48 MPa. В A 60 MPа Determine the principal planes. The principal planes are at and
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
Part 2,3,4
9-10 Determine the equivalent state of stress on an element if it is oriented 30° clockwise from the element shown. Use the stress-transformation equations. 300 psi 950 psi
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28500 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.62 in.² and bar (2) has a cross-sectional area of 0.38 in.². After load P is applied, the strain in bar (1) is found to be 670 μe. Assume L₁=68 in., L₂=94 in., a-35 in., b=39 in., and c-22 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a L2 b C D P
CN=44
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: Using the method of equilibrium, and NOTE: support your answer with sketches and the FBD.
Please use Mohr's Circle.