A guy wire for an antenna tower is to be alumi-num, having an allowable stress of 12 000 psi. Ifthe expected maximum load on the wire is 6400 lb,determine the required diameter of the wire.3-7.

Given data as per question Allowable stress = 12000 psi Maximum load = 6400 lb

Answered: A guy wire for an antenna tower is to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A column is clam- ped at the bottom and is carrying a vertical load F at the center of F, F the top cross section and a horizon- tal load F in the middle of edge b. The column is made of 3 layers with different Young's moduli. Determine the normal stress distri- bution in the cross section at the clamping. 4E
only HANDWRITTEN answer needed ( NOT TYPED)
3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stress between the pin and the bar is (0,)allow = 30ksi , determine the dimension w and t so that the gross area of the cross section is wt = 2in² and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the prjjected area whenj calculating the bearing stress.) t d w/2 w/2
Find bearing stress in the Revit connection of 15 mm diameter, if the applied load (P= 15 kN), the thickness of the plate is 20 mm. P P 140 mm 20 mm 20 mm P
If the overhanging beam is made of wood having the allowable tensile and compressive stresses of 4Mpa and 5Mpa, determine the maximum concentrated force P that can be applied at the free end. Can you also please explain the calculation of centroid. I'm a bit confused of the values that I need to use. Thank you
Handwritten solution required (include diagram if possible)
The composite bar is firmly attached to unyielding supports. Compute the stress in each material caused by the application of the axial load P = 320 kN.
A tie rod of ¼ inch diameter is used to hold a plaster wall in place. The tensile stress in the rod caused by load P is 20 ksi. Find the diameter “d” (to the nearest 1/6 inch) of the washer that keeps the bearing stress between the plaster and the washer from exceeding 300 psi.
مقاومة المواد
Q: The aluminum bar of circular cross section is attached to rigid supports at A and C. Calculate the maximum stress in each segment after the load (30 kN) is applied. Use E = 70 GPa. .400 mm- 250 mm- 30 kN 100 mm 50 mm
Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of the rod is steel (E = 200 GPa), what is the change in length of the rod?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A guy wire for an antenna tower is to be alumi- num, having an allowable stress of 12 000 psi. If the expected maximum load on the wire is 6400 lb, determine the required diameter of the wire. 3-7.