a) g(t)*z(t) Du b) y(t)*z(t) c) g(t)*y(t)

Q: The average value of a sinusoidal current is 100 A. Its r.m.s. value is ............ (1) 63-7 A…

A: Given: Average value of a sinusoidal signal is Vavg=100 A.

Q: 8. Find the electric potential at the following green points: a) b) 1552 2012 9V Ath -2012

A: Given,

Q: 9. [(2260)/(15Z-75)]+[(1.2+j1.2)/(4.2+j2.4)]

A:

Q: The distorted waveform in power distribution system contains only odd-harmonic components O True…

A:

Q: Impedance of AC circuit and Admittance of AC circuit SHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN…

A:

Q: In stormy weather, Corona occurs at a much higher Voltage compared to fair weather. Select one: True…

A: In the stormy weather, the number of ions is more than normal, and corona occurs at much less…

Q: Find the rms value of the given voltage wave 2 3

A: RMS of AC is that value which when passes through a resistor of known value for a particular…

Q: Find: (a) Vp VP-P Vp-p (b) (c) Frequency (d) Period (e) Angular Velocity (f) Phase angle (g)…

A: Given waveform:-

Q: Find the RMS value of V-100 sin(377t+76) V

A: Equation of voltage is given as, vt=100sin377t+760 V.

Q: The current that varies sinusoidally with time. Blank 1

A: Current  is defined as rate of flow of electron in a conductor.

Q: tion 1: what is the phase relationship between the sinusoidal waveforms of each of the following…

A: Brief description: For the above given current and voltage sinusoidal signals we need to justify…

Q: Q4/ Find the voltage average and the voltage waveform for the output of the circuit shown below.…

A: VAvg= 2V/pi VRMS=V/sqrt(2) Where V= peak voltage

Q: he sinusoidal waveform 4.35 Ohm Xc-5.52 E-100V

A:

Q: The frequency is known as ohms but many times, it is referred to as cycles. Select one: TRUE FALSE

A: To discuss whether the given statement is correct or not. Statement: The frequency is known as ohms…

Q: A sinusoidal current has a rms value of 3 amperes, its peak to peak value will be 2.1213 amp O 3.46…

A:

Q: for 下e energy FiND Tellowing Synal ン(り- loe もろ0 the -ヒ loe くo

A:

Q: A sinusoidal current has a rms value of 3 amperes, its maximum value will be O 2.1213 amp 3.46 amp…

A:

Q: Question 1.) Fill in the blanks with proper wording a.) For a purely resistive circuit, the voltage…

A: Fill the blank  What is relationship between current phasor and voltage phasor in case of  1.…

Q: Q/Exprees the de cinaluunber (85)(-85),2 see complemurst)

A:

Q: 4. After MOV AL, A0H DAA AL=

A: After the mov operation, AL will carry A0H.

Q: In the shown figure the circulation of A= pa, is on 7. 2. 60° 30° 2. Windows bu

A: Circulation of vector A is the line integration of the A along path.  i.e. ∮ A.dl We will calculate…

Q: A2a R A26 Figure Q3a Figure Q3a shows the circuit schematic of part of an instrumentation amplifier.…

A:

Q: 9. What is sinp from impedance triangle? a) Xµ/R b) XĻ/Z c) R/Z d) Z/R

A: we need to find out sin phai  value.

Q: How can you tell which phasor is lagging when the two phasors don’t start in the same location such…

A: It is given that:

Q: EXPRESS (j-3)¹⁹ IN RECTANGULAR FORM.

A:

Q: Alternating currents (AC) is current (or voltage) that take on same values as they change with time…

A: In this question we need to verify the given statement is true or false.

Q: A triangular voltage source has a peak value of 10 V. What is the computed RMS value of this source?…

A:

Q: A sinusoidal current has a rms value of 3 amperes, its maximum value will be O 3.46 amp O 0.866 amp…

A:

Q: Oscilloscope measurements indicate that the peak voltage across a load and the peak current through…

A: In this question,  We need to determine the power factor.  We know  Power factor = cos(θ) = cos(V^I)…

Q: The time constant RC has a unit of

A: In this question,  We need to choose the correct options What is unit of the time constant RC?

Q: Compute and present the answer in both rectangular and polar form: a) (2/-10°) (5-j5) +20/15°…

A: Given ExpressionsHere we need to compute the given expressions and answer them in both rectangular…

Wheatstone Bridge Method

A Wheatstone bridge is a circuit used to measure unknown resistance by measuring the ratios of the two branches of the circuit such that each branch has two resistance and out of four resistance one is unknown. The two branches are joined in between with the help of galvanometer which is used to determine the direction of the current. The main advantage of this circuit is that it can provide the most accurate measurement (different from a simple voltage separator).