A graduate cylinder of water is filled such that the pressure at the bottom of the cylinder is 978 Pascals (gauge). If the density of the water is 997 kg/m3 determine the height of the water column in units of centimeters.

Q: The force required to slip one layer of a fluid past another with a given velocity is * O Rate of…

A:

Q: Q2 // The diameter of a pipe at section 1 and 2 are 10 cm and 15 cm respectively. Given velocity of…

A: Given that, The diameter of the pipe at section 1 D1 = 10 cm = 0.1 m The diameter of the pipe at…

Q: For a flow over a flat plate the normalized velocity profile is --² where y is in mm 2 U a)…

A: Answer: a) we know that, Displacement Thickness = δ* = ∫0δ (1- uU) dy  Displacement Thickness = δ* =…

Q: Suppose that exactly half of the annular volume between concentric, horizontal cylinders is filled…

A:

Q: Slug flow of pipes

A: Slug flow is a type of multi-phase flow. Multi-phase flow is simply fluid flow which contains…

Q: If a spherical drop of liquid evaporates at a rate proportional to its area, if initially its radius…

A: Let V and S be volume and surface area of the spherical drop whose radius at time t is r Given…

Q: The Reynolds number is a dimensionless number used to categorize the fluids systems in which the…

A: Write the expression for Reynolds number as follows: Re = DuρμRe = Duv      ......1   Here, Re is…

Q: 5. The cylindrical vessel in the right figure is full of water at a pressure of 1000 psig. The top…

A:

Q: For the water flow at 20 °C, use the manometer measurement to estimate the (a) centerline velocity…

A:

Q: Consider a uniform flow of a liquid with density and viscosity equal to 760 kg/m³ and 0.05 Pa s past…

A:

Q: Q3: The flowrate of a fluid in a pipe is measured using a pitot tube which gives a pressure…

A: Perform force balances for streamline flow in pipe:

Q: a cubic reservoir has side of 10 meters. if it is initially half full with water by height,…

A: Given, Side=10 m Height of water, h=5 m

Q: There is a drop in the bubble with the diameter of 10mm and pressure of 250 KN/m?. If the surface…

A: In fluid mechanics, surface tension is defined as the property of the surface of a liquid allows it…

Q: A nozzle is bolted onto a pipe by the flanged joint as shown in the Agure. The flowing fluid is…

A:

Q: 4. Water flows through a smooth horizontal 2 m long tube of 2 mm diameter with an average velocity…

A:

Q: Suppose that exactly half of the annular volume between concentric, horizontal cylinders is filled…

A:

Q: An oil film drains steadily down the side of a vertical wall, as shown on figure below. After an…

A: Oil film is steadily sliding down on a vertical wall and as it reaches down its thickness increases…

Q: As flow meters, these devices mechanically divide a fluid stream into discrete, known volumes and…

A:

Q: Unit for mass flow rate and molar flow rate

A: The mass flow rate is defined as the differential mass of the fluid flowing per unit of time. The…

Q: D

A: The flow of Fluid in Pipe

Q: Shear stress of the fluid will be maximum at the a. Wall of the pipe O b. In between center and wall…

A: 1) Answer: a. wall of the pipe Shear stress of the fluid is maximum at the wall because at the wall…

Q: two plates which are aligned parallel above eachother.The top plate is moving horizontally with a…

A: A Newtonian fluid is flowing between two parallel plates where top plate is moving with a constant…

Q: A fluid is placed between two large parallel plates. The distance between the plates is 5 mm. The…

A: a) The momentum flux (or force per unit area) is τfyz=FA=0.5+22.5=1 Pa b) Let V2 be the velocity of…

Q: The pressure drop AP over a length L of pipe is assumed to depend on the average velocity V,the…

A: Pressure drop=∆P Length of the pipe=L Average velocity=V The pipe diameter=D The average height of…

Q: A 1-m deep, open container is filled with an unknown fluid. The absolute pressure of the fluid at…

A: The specific gravity of the fluid is the ratio of the density of the fluid to the density of the…

Q: A hydrometer is calibrated such that in pure water it reads exactly 1.0 at the air- water interface.…

A:

Q: 17.17. The fins on the radiator of your car are about 2 in long. When your car is going 60 mi/h, the…

A: length of fin x=2 inchvelocity approaching the fins  v=40 mi/hr = 17.88 m/s

Q: Pressure is expressed as the equivalent O True O False height of a fluid column.

A: Pressure is defined as the ratio of force acting per unit area. P = ForceareaP = mgA

Q: Parallel laminar Flow Between Infinite Planes with a Manometer A Newtonian fluid with viscosity μf…

A:

Q: 3. Determine the pressure exerted on the surface of a submarine cruising 175 ft below the free…

A:

Q: 4.) A metallic body floats at the interface of mercury of specific gravity 13.6 and water in such a…

A:

Q: Solve this question using geometry and drawing To steady a sign as it is being lowered, two cables…

A:

Q: The flow behavior of a polymer melt with a specific gravity of 1.17 and a viscosity of 0.486…

A:

Q: True or false: Osmotic pressure can be explained by the difference in fugacities

A: It is to be mentioned whether fugacity difference explains the osmotic pressure or not.

Q: What is Reynolds number used in Chemical Engineering calculations. Also give its flow conditions

A: Reynolds number is defined as the ratio of the inertia force to the viscous force. This is an…