A glass U-tube open to the atmosphere at both ends is as shown. If the tube contains, oil and water as shown, determine the specific gravity of oil, unit weight of water is 9.79 kW/m

Q: 2 - Two concentric cylinders are covered by a rigid plate that carries an axial load, as shown in…

A: Rise in temperature, T

Q: A solid cylinder is to be 0.25 m in diameter. The base of axial length 25 mm is to be of metal which…

A: Given, Diameter of cylinder = 0.25 m Length of metal cylinder = 25 mm Specific gravity of metal = 7…

Q: For the pressure vessel containing glycerin, with piezometer attached as shown, what is the…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: The cyclindrical tank w ends shown in the figur volatile liquid and its v density is 800 kg/m³, a is…

A:

Q: The unit weight of water at 50°F is 62.4 pcf. If the volume of the vessel that contains water is…

A:

Q: 10. Calculate the density, specific weight, and specific volume of chlorine gas at 25°C and pressure…

A:

Q: A glass tube of 2.5 mm internal diameter isimmersed in oil of mass density 940kg/(m^3 to adepth of 9…

A: Diameter of tube = 2.5 mmMass density of oil = 940 kg/m3Depth = 9 mmPressure = 148 N/m2To Find :The…

Q: Calculate the capillary effect in mm in a glass tube of 4 mm diameter, when immersed in (i) water,…

A: Given data : Diameter (d)=4 mmDensity of water (ρW)=998 kg/m3Surface tension of water (σW)=0.073…

Q: Calculate the density, specific weight, and specific volume of oxygen at  and 40 kPa abs. b. If the…

A:

Q: the answer for a is 40.3 degree Celsius. please answer letter B only. thank you

A: Given data in question Length Aluminum rests freely on ground. Steel bar is 5mm longer Coefficient…

Q: What is the mass M that must be suspended at the left to hold the system in equilibrium in the…

A:

Q: 4. For the vessel containing glycerin under pressure, calculate the total pressure at the bottom of…

A: Given Data Air pressure (Pa) = 50 kpa = 50 × 103 N/m2  Determine the total pressure at bottom of…

Q: . A certain liquid has a specific weight of 8000 N/m³. Compute its specific volume.

A: 3

Q: The air exits the nozzle to the atmosphere and enters a vertical plate as shown in the figure. it…

A: Assumptions: 1. The flow is incompressible 2. The flow is frictionless.

Q: A glass U-tube open to the atmosphere at both ends is shown. If the U-tube contains oil and Liquid X…

A: Using the manometric equation. Writing the pressure equation the value of SG of oil can be…

Q: The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid…

A: To Determine (a) the gage pressure reading on the pressure gage Pressure gage is 1m below the liquid…

Q: Liquid A, B, and C in the container shown below have specific gravities of 0.80, 1.00 and 1.60,…

A:

Q: Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It…

A:

Q: An aluminum pipe has a length of 70 m at a temperature of 20°C. An adjacent steel pipe at the same…

A: Answer  We are given Aluminium pipe Length La = 70 m steel pipe length Ls = 70 + 0.010 = 70.010 m…

Q: The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid…

A: Reference : Fluid mechanics, Pressure analysis for Volatile liquid. We know that , Gage pressure is…

Q: Chamber A oil SE=0.89 0.30 mercury Chamber B tetrachloride sg=1.59 0.8 m

A:

Q: A fireworks shell P is launched upward from point A and explodes at its apex at an altitude of 265…

A: Solution-The given values ase as follows,Altitude =265ftAltitude y=175ftTo determine Part…

Q: In the figure shown, determine the difference in pressure between points A and B. Kerosene, s- 0.82t…

A:

Q: Consider a soap bubble 2mm in diameter and a droplet of water also 2mm in diameter that are falling…

A: Soap bubble diameter, d1=2 mm Water droplet diameter, d2=2 mm Surface tension of film of soap…

Q: Calculate the dynamic viscosity of an oil, used for lubrication between a shaft and sleeve. The…

A: Given Data : shaft diameter, D= 0.4m and shaft radius ,r=0.2 m Speed of shaft, N=190 rpm Shear…

Q: 1  Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in Figure Q1 (a), can…

A:

Q: 10 cm diameter solid cylinder of height 10 cm and weighing 0.40 kg is immersed in a liquid (800…

A:

Q: Water in the pipe is shown in the figure. Determine the pressure at Point A in kPa(abs), to the…

A: Given Data for first question: Height of mercury=135 mm specific gravity of mercury=13.54 Height…

Q: Calculate the capillary effect in mm in a glass tube of 4 mm diameter, when immersed in mercury. The…

A: Given- Diameter of the glass tube d=4 mm, Surface tension = 0.57 N/m, Angle of contact=130o, It is…

Q: Oil flows through a pipe as shown in the figure below. The coefficient of discharge for the orifice…

A:

Q: to a depth of 100mm and rest with air. What is the pressure at the bottom of the periphery of the…

A:

Q: The specific gravity of a liquid is 0.75. What height (in m) of that liquid is needed to provide a…

A: Specific gravity of liquid = 0.75 Pressure difference = 30psi To find out the height of liquid for…

Q: A glass U-tube open to the atmosphere at both ends is shown. If the U-tube contains oil and Liquid X…

A:

Q: A U-tube of uniform cross-section has both arms open to the atmosphere. The U-tube contains three…

A:

Q: A soap bubble 50 mm diameter has an pressure in excess of the outside pressure of 25 N/m2. Calculate…

A: Given data : Diameter (d)=50 mmPressure inside droplet above outside pressure (P)=25 N/m2

Q: For a gauge pressure of A of -10.89 kPa, what is the specific gravity of the gauge liquid B in the…

A:

Q: A capillary tube of diameter 2 mm is placed in a reservoir of water, and a similar capillary tube is…

A:

Q: 10° M 40kg 20 kg

A:

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.