A) Given the magnetic circuit of Figure below, assume B = 0.6 T at the midpoint of the left legand find: (a) Vm,airi (b)Vm,steel; (c) the current required in a 1300-tum coil linking the left leg.S₁=5 cm²L$₂=3 cm²L₁ = 8 cmL₂=16 cmMaterial: silicon steel÷0.5 cmB (T)1.41.21.00.80.60.40.20100300500H (A-t/m)700900

Given: L1=8cm L2=16cm B=0.6T S1=5cm2 S2=3 cm2 l= 0.5cm N=1300- turn coil Vmair =? Vm (steel)=?…

A) Given the magnetic circuit of Figure below, assume B = 0.6 T at the midpoint of the left leg and find: (a) Vm,air; (b)Vm,steel; (c) the current required in a 1300-turn coil linking the left leg. S₁5 cm² $₂=3 cm² L₁ = 8 cm L₂= 16 cm Material: silicon steel 18 0.5 cm B (T) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 100 300 500 H(f/m) 700 900

A) Given the magnetic circuit of Figure below, assume B = 0.6 T at the midpoint of the left leg and find: (a) Vm,air; (b)Vm,steel; (c) the current required in a 1300-turn coil linking the left leg. S₁5 cm² $₂=3 cm² L₁ = 8 cm L₂= 16 cm Material: silicon steel 18 0.5 cm B (T) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 100 300 500 H(f/m) 700 900

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

TRUE OR FALSE Ultimate tensile strength has the same value to yield strength in brittle materials. If bulk material is being subjected to tensile stress, slip will occur. In the presence of magnetic field, ferromagnets increase the magnetic flux density. In terms of properties, sandwich panels have isotropic.
A magnetic ring has a mean circumference of 20 cm and a cross-section of 20 cm² and has 800 numbers of turns of wire. When the exciting current is 5 A, the flux is 2 mWb. The relative permeability of iron is nearly
13 - Which of the following is true about the magnetic field in the Biot-Savart law?I. is inversely proportional to r.II. It is inversely proportional to r2.III. It is directly proportional to the current. A) Yalnız I B) II ve III C) Yalnız III D) I ve III E) Yalnız II
Q2. Determine the current Ii required to establish a flux of o -4 x 10 Wb in the magnetic circuit of figure below, draw the equivalent circuit and find the circuit inductance given (4. - 2800 H/m). Lg - 0.2 cm Sheet Steel I I-0.28 A N2 - 200 turns A- 1.6 x 10+ m' N - 40 turns Labed - 20 cm
Consider the magnetic circuit given in below figure with parameters: u=153 Ho, d1=9 cm, d236.2 cm, d3=7.9 cm, da=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 d, Tolerance + 0.1 relative
Consider the magnetic circuit in Figure. Assuming that the core µ= 1000µo has a uniform cross section of 4 cm2,N= 400 , the flux density in the air gap. 0.2 A L = 42 cm 4 = 0.1 cm 35.4 mwb 60.5 mwb 70.8 mwb Non of These
If phase sequence is acb then phase voltage Va, Vb and Vc are respectively Select one: a. 231/-30o , 231/90o , 231/-150o b. 231/60o , 231/180o , 231/-90o c. 231/-30o , 231/-150o , 231/90o d. 231/ 0o , 231/120o , 231/360o
Q1. Figure 1 shows the magnetic circuit with cross section area of core, 1000 mm2 and current source, 10 mA. By assuming the absolute permeability of core is 2.513x103 H/m, analyze the circuit and determine the following parameters: a. Draw the equivalent Ampere Circuital Law model b. Total reluctance of magnetic circuit c. Magnetic flux at centre and both sided d. Magnetic flux density at centre and air gaps e. Magnetic flux strength at centre and air gaps f. Briefly explain, effect to the magnetic circuit if the length of air gaps keep decreasing and increasing. at 7 cm 30 cm 30 cm 7 cm 7 cm 30 cm 1 cm 400 turns 1 cm 7 cm Figure 1 B-H CURVE BIT) 16 Sheet steel Cast steel 14 12 1.0 08 Cast iron 0.6 04 0.2 H(AUm) 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
A magnetic core in the form of a closed circular ring has a mean length of 30 cm and a cross sectional area of 1 sq cm. Determine the reluctance if the relative permeability of iron is 2400
Please answer second question, and can it be hand written because i find typed work difficult to follow
Home work 1.... > Home work in Electrical Machine 1- For the series magnetic circuit of Figure below A = 2 x 10-3 m? N = 400 turns Cast-steel core 1 = 0.16 m (mean length) a) Find the value of I required to develop a magnetic flux of 4 = 4 x 10 Wb. H(Cast steel) = 170 At/m b) Determineu and ur for the material under these conditions. 2- A) What is the basic nature of nature of the induced EMF in a d.c generator? b) What is the function of a commutator? 3- Prove that NI
Consider the magnetic circuit given in below figure with parameters: u=153 Ho,d1=9 cm, d2=6.2 cm, d3=7.9 cm, d4=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 N Tolerance + 0.1 relative