A generator has a square coil consisting of 640 turns. The coil rotates at 96 rad/s in a 0.350 T magnetic field. The max (peak) output of the generator is 170 V. What is the length of one side of the square coil? (Note: if needed information related to squares: perimeter = 4L, area = L²) 0.0761 m 0.0889 m 0.0352 m 0.0557 m 0.0455 m

A generator has a square coil consisting of 640 turns. The coil rotates at 96 rad/s in a 0.350 T magnetic field. The max (peak) output of the generator is 170 V. What is the length of one side of the square coil? (Note: if needed information related to squares: perimeter = 4L, area = L²) 0.0761 m 0.0889 m 0.0352 m 0.0557 m 0.0455 m

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter23: Electromagnetic Induction, Ac Circuits, And Electrical Technologies

Section: Chapter Questions

Problem 34PE: (a) A car generator turns at 400 rpm when 1he engine is idling. Its 300-turn, 5.00 by 8.00 cm...

See similar textbooks

Similar questions

An astronaut is connected to her spacecraft by a 25-m-long tether cord as she and the spacecraft orbit Earth in a circular path at a speed of 3.0 105 m/s. At one instant, the voltage measured between the ends of a wire embedded in the cord is measured to be 0.45 V. Assume the long dimension of the cord is perpendicular to the vertical component of Earths magnetic field at that instant. (a) What is the magnitude of the vertical component of Earths field at this location? (b) Does the measured voltage change as the system moves from one location to another? Explain.
A square, flat loop of wire is pulled at constant velocity through a region of uniform magnetic field directed perpendicular to the plane of the loop as shown in Figure OQ31.5. Which of the following statements are correct? More than one statement may be correct. (a) Current is induced in the loop in the clockwise direction. (b) Current is induced in the loop in the counterclockwise direction. (c) No current is induced in the loop. (d) Charge separation occurs in the loop, with the top edge positive. (e) Charge separation occurs in the loop, with the top edge negative. Figure OQ31.5
Transcranial magnetic stimulation (TMS) is a noninvasive technique used to stimulate tedious of the human brain (Figure P31.3). In TMS, a small coil is placed on the scalp and a brief burst of current in the coil produces a rapidly changing magnetic field inside the brain. The induced emf can stimulate neuronal activity. (a) One such device generates an upward magnetic Held within the brain that rises from zero to 1.50 T in 120 ms. Determine the induced emf around a horizontal circle of tissue of radius 1.60 mm. (b) What If? The field next changes to 0.500 T downward in 80.0 ms. How does the emf induced in this process compare with that in part (a)? Figure P31.3 Problems 3 and 51. The magnetic coil of a Neurostar TMS apparatus is held near the head of a patient.
(a) A car generator turns at 400 rpm when 1he engine is idling. Its 300-turn, 5.00 by 8.00 cm rectangular coil rotates in an adjustable magnetic field 50 that it can produce suf?cient voltage even at low rpms. What is the field strength needed to produce a 24.0 V peak emf? (b) Discuss how this required field strength compares to those available in permanent and electromagnets.
Magnetic field values are often determined by using a device known as a search coil. This technique depends on the measurement of the total charge passing through a coil in a time interval during which the magnetic flux linking the windings changes either because of the coils motion or because of a change in the value of B. (a) Show that as the flux through the coil changes from 1 to 2, the charge transferred through the coil is given by Q = N(2 1)/R, where R is the resistance of the coil and N is the number of turns. (b) As a specific example, calculate B when a total charge of 5.00 104 C passes through a 100-turn coil of resistance 200 and cross-sectional area 40.0 cm2 as it is rotated in a uniform field from a position where the plane of the coil is perpendicular to the field to a position where it is parallel to the field.
Review. In Figure P30.42, a uniform magnetic field decreases at a constant rate dB/dt = K, where K is a positive constant. A circular loop of wire of radius a containing a resistance R and a capacitance C is placed with its plane normal to the field. (a) Find the charge Q on the capacitor when it is fully charged. (b) Which plate, upper or lower, is at the higher potential? (c) Discuss the force that causes the separation of charges. Figure P30.42
The bar in Figure OQ31.6 moves on rails to the right with a velocity v,. and a uniform, constant magnetic field is directed out of the page. Which of the following statements are correct? More than one statement may be correct. (a) The induced current in the loop is zero. (b) The induced current in the loop is clockwise. (c) The induced current in the loop is counterclockwise. (d) An external force is required to keep the bar moving at constant speed. (e) No force is required to keep the bar moving at constant speed.
Eddy current are induced currents set up in a piece of metal when it moves through a nonuniform magnetic field. For example, consider the flat metal plate swinging at the end of a bar as a pendulum, as shown in Figure CQ20.9. (a) At position 1, the pendulum is moving from a region where there is no magnetic field into a region where the field B is directed into the paper. Show that at position 1 the direction of the eddy current is counterclockwise. (b) At position 2, the pendulum is moving out of the field into a region of zero field. Show that the direction of the eddy current is clockwise in this case. (c) Use right-hand rule number 2 to show that these eddy currents lead to a magnetic force on the plate directed at shown in the figure. Because the induced eddy current always produces a retarding force when the plate enters or leaves the field, the swinging plate quickly comes to rest. Figure CQ20.9
A 50-turn rectangular coil with dimensions 0.15m0.40m rotates in a uniform magnetic field of magnitude 0.75 T at 3600 rev/min. [a) Determine the emf induced in the coil as a function of time, (b) If the coil is connected to a 1000 resistor, what is the power as a function of time required to keep the coil turning at 3600 rpm? (c) Answer part (b) if the coil is connected to a 2000 resistor.
What is the value of the magnetic flux at coil 2 in Figure 23.56 due to coil 1? Figure 23.56 (a) The planes of the two coils are perpendicular. (b) The wire is perpendicular to the plane of the coil.
A magnetized sewing needle has a magnetic moment of 9.70 mA m2. At its location, the Earths magnetic field is 55.0 T northward at 48.0 below the horizontal. Identify the orientations of the needle that represent (a) the minimum potential energy and (b) the maximum potential energy of the needlefield system. (c) How much work must be done on the system to move the needle from the minimum to the maximum potential energy orientation?
A rectangular loop has dimensions 0.500 m by 0.300 m. The loop is hinged along the x-axis and lies in the xy-plane (Fig. P19.42). A uniform magnetic field of 1.50 T is directed at an angle of 40.0 with respect to the positive y-axis and lies parallel everywhere to the yz-plane. The loop carries a current of 0.900 A in the direction shown. (Ignore gravitation.) (a) In what direction is magnetic force exerted on wire segment ab? What is the direction of the magnetic torque associated with this force, as computed with respect to the x-axis? (b) What is the direction of the magnetic force exerted on segment cd? What is the direction of the magnetic torque associated with this force, again computed with respect to the x-axis? (c) Can the forces examined in parts (a) and (b) combine to cause the loop to rotate around the x-axis? Can they affect the motion of the loop in any way? Explain. (d) What is the direction (in the yz-plane) of the magnetic force exerted on segment bc? Measuring torques with respect to the x-axis, what is the direction of the torque exerted by the force on segment bc? (e) Looking toward the origin along the positive x-axis. Will the loop rotate clockwise or counterclockwise? (f) Compute the magnitude of the magnetic moment of the loop. (g) What is the angle between the magnetic moment vector and the magnetic field? (h) Compute the torque on the loop using the values found for the magnetic moment and magnetic field. Figure P19.42