A gas undergoes the cyclic process shown in the PVdiagram at right. In the process abc, the systemabsorbs 4500 J of heat. The internal energy of thegas at a is U₁= 600 J.(b)(c)How much work is done on or by the gasfrom a to b?How much work is done on or by the gaswhen it goes from b to c ? Note that the vertical scaleis measured in kilo-Pa-100 kPa -105 Pa[1 Liter = 10³ m³]100The net heat absorbed by the gas during the complete cycle is 1000 J.(d) Determine the heat entering or leaving in the process c to a50a20Use the First Law of Thermodynamics to determine the internal energy of the gas at c, Uc60CLiters

Given, The heat absorbed, Qabc=4500J The internal energy at a, Ua=600J a. The volume is constant…

Answered: A gas undergoes the cyclic process…

Similar questions

0.5 mole of an ideal monatomic gas starts from 500 point a in the diagram to the right. It undergoes a a b 400 constant pressure expansion from a to b; a constant volume compression from b to c: and an isothermal a200 compression from c to a. 200 From last week, find the three temperature values Ta, To and T. and the total work for one cycle W. Now find the heat added along the three processes 100 Qab, Qbc and Qca and the efficiency of this process. 2 4 Find the change in entropy along each process Sabı Spc and Sca and the total entrophy change. volume (m³) pressure (Pa)
A gas follows the PV diagram in the figure below. Find the work done on the gas along the paths AB, BC, CD, DA, and ABCDA.
A 0.25 mol of a monatomic ideal gas at 27 degrees C is contained in a cylinder that is fitted with a movablefriction free piston. The temperature of the gas is increased to 127degrees C while the pressure of 1 atm ismaintained. Calculate:i. how much work is done by the gas in the process, ii. the change in internal energy of the gas, iii. heat that was supplied to the gas.
Needs Complete typed solution with 100 % accuracy.
In the process illustrated by the pV diagram in the image, the temperature of the ideal gas remains constant at 136 ∘C . Part A: How many moles of gas are involved? Part B: What volume does this gas occupy at a? (express in cubic meters) Part C: How much work was done by or on the gas from a to b? and by how much did the internal energy of the gas change during this process?
A monatomic gas in a certain gasoline engine undergoes an Otto cycle. a.) Assume that the pressure is increased by a factor of 1.5 during the adiabatic compression stroke, so that the pressure after this step is P2 = 1.5 P1, where P1 is the initial pressure. Write an equation for the volume V2 in terms of the volume before this step V1. b.) Write an equation for the temperature T2 after the adiabatic compression in terms of the temperature T1 before this step. c.) Assume the pressure is doubled after the isochoric step, such that the pressure after this step is P3 = 2.0 P2. Write an equation for the temperature after this step T3 in terms of a number (carried to two digits) multiplied by the temperature T2 before this step.
Problem 4: Consider a cylinder with a movable piston containing n moles of an ideal gas. The entire apparatus is immersed in a constant temperature bath of temperature T Kelvin. The piston pushes slowly outward on an external body which matches the force momentarily at each instant so that the gas expands quasi-statically from a volume V1 to V2 at constant temperature T. The isothermal process is shown in the figure above, where the pressure p is related to the volume V by the ideal gas law as follows: pV = nRT, where R is the gas constant. Part (b) For n = 3 moles, T = 350 K, and V2 = 2.5V1, determine the work done by the gas on the external body. The gas constant is R = 8.314 J K-1 mol-1.
How do I go about this question?
= 2 is taken through a cycle as shown in the figure to the right, which is not necessarily drawn to scale. n moles of an ideal gas with adiabatic index Y The cycle proceeds as follows: 1– 2 is an isobaric compression to V2= Vo/2 2 – 3 is an isochoric process with P3 = 3P0 3 – 4 is an isothermal compression to V4 = Vo/4 4 – 5 is an isochoric heating process 5 – 1 is an adiabatic expansion back to Vo ЗРо Ро Vo/4 Vo/2 Vo (a) at constant pressure, What are Cv, the molar specific heat at constant volume, and Cp, the molar specific heat for this gas? Your answer should be in terms of n, R, T , or a subset of these quantities. (b) ( diagram) in terms of Po, and the temperatures T,, T3 , T4 , and T3 (the temperatures at points 2 – 5) in terms of To. All work must be shown. Find the unknown quantities P4 and P5 (which are the pressures at points 4 and 5 on the (c) Find the work done on the system in terms of n, R, T, , and pure numbers only for the 3, 3 → 4, 4 → 5, and 5 → 1. Make sure to show…