A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is d =8 cm, and it reduces to d = 3.74 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with hose nozzle water, determine average velocity (m/s) of water at the nozzle exit. Nozzle Garden hose Bucket

A garden hose attached with a nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is d =8 cm, and it reduces to d = 3.74 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with hose nozzle water, determine average velocity (m/s) of water at the nozzle exit. Nozzle Garden hose Bucket

Name: A garden hose attached witha nozzle is used to fill a 20 Liters bucke
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A garden hose attached witha nozzle is used to fill a 20 Liters bucket. The inner diameter of the hose is d=8 cm, and it reduces to d= 3.74 cm at the nozzle exit. If it takes 50 seconds to fill the bucket withhosenozzlewater, determine average veloc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as shown below, isinclined at a 30° angle with the horizontal. Calculate the pressure differencein KN/m²between the smaller and bigger diameter parts of the pipe if the velocity of water at the smaller diameter section is 6.56 ft/s. Pi. V₁.d₁. A1 41-0 P2. Vz, dz. Az 32 Datum
Please assist me with this question as soon as possible.
A hose is connected on one side to a tall tank containing water and theother side is lying on the ground. Once the open side is lying on the groundit has water coming out of it at a speed of 7.4 meters per second. Howmuch do you need to lift the hose to stop water coming out of it?
fluid mechanics Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m3/s. At the nozzle inlet, the diameter is 5 cm and the pressure is 200 kPag. The nozzle discharges freely to outside air. Determine the velocity of the water (in m/s) as it exits the nozzle. Assume negligible head losses through the nozzle. Round your answer to 2 decimal places.
Full part of question b
On a trip to the beach (Patm 1 atm or 101.3 kPa), a car runs out of gasoline and it is necessary to siphon gasoline from a Good Samaritan's car. The siphon is a hose with a small diameter and to start the action it is necessary to insert one end into the tank full of gasoline, fill the hose with it through suction and then put the other end in a can that is placed under the tank level. The difference in pressure between point 1 (on the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the highest elevation to the lowest. In this case, point 2 is located 0.75 m below point 1, and point 3 is 2 m above 1. The siphon diameter is 4 mm and friction losses in it must be ruled out. Determine: a) theminimum time to bring 4 L of gasoline from the tank to the can and b) the pressure at point 3. The density of the gasoline is 750 kg / m3.
A hydraulic turbine receives water from a reservoir of 50 meter above it. What is the minimum flow rate in kilograms per second to produce a steady turbine output of 30 MW
There is a storage tank with a height of 5 m. Initially the tank is empty. The cross- sectional area of the tank is 1m?. There is a hole in the storage tank at a level of 2m from the bottom of the tank. The relationship between the volumetric flowrate through the hole and the level of the tank is q=vh. In addition there are two valves at the top and bottom of the tank for inlet and outlet streams. Suddenly, the two valves at the top and bottom of the tank are opened where inlet and outlet stream volumetric flowrates became 1m/s and 0.2m2/s. a)Determine the time for the liquid level to reach 2m
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: A) Neglecting friction, the volume flow rate of airB) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
We have a tank (large enough to neglect the velocity of the fluid surface in the tank v1 =0). The tank contains water at a mevel of 15 meters. The tank is enclosed and the air space above the water is at 5 atm. The exit of the tank consists of 25 meters of 2 cm diamter pipe with d/D = 0.0004. It exhaust to the atmospere at 1 atm. What is the exit velocity?
If the pressure head, velocity head and the potential head at a point in a fluid flow inside a pipeline are 2.1 m 1.9 m and the 4 m respectively, the Total head at that point is Om 6.1 m 8 m 4 m
The pump is used to transfer fluid from one location to another of different height. At inlet and outlet atmospheric conditions are present. The pipe diameter increases after the pump outlet. Determine all the surviving terms of energy equation after simplification. FUM kinetic energy, potential energy, pipe losses none pipe losses, potential energy, pressure increase pressure increase, pipe losses, potential energy kinetic energy, pressure increase, pipe losses OOO