A furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal conductivities of 1.65, k and 9.2 W/m K respectively. The inside is exposed to gases at 1250'C with.convection of 25 W/mK, and the inside surface is at 1100 C. the outside surface aif at 25 C with convection of 12 W/m K. Which formula from figure 2 is applicable to overall heat transfer coefficient 7

A furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal conductivities of 1.65, k and 9.2 W/m K respectively. The inside is exposed to gases at 1250'C with.convection of 25 W/mK, and the inside surface is at 1100 C. the outside surface aif at 25 C with convection of 12 W/m K. Which formula from figure 2 is applicable to overall heat transfer coefficient 7

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flat wall is exposed to an environmental temperature of 38oC. The wall iscovered with a layer of insulation 2.5 cm thick with a thermal conductivity of 1.4W/moC, and a temperature of the inside wall is 315oC. The wall loses heat to theenvironment by convection. Compute the value of the convective heat transfercoefficient that must be maintained on the outer surface of the insulation to ensurethat the outer surface temperature does not exceed 41oC
Calculate the heat transfer rate per metre length when a steel pipe conveying steam is insulated. The pipe has an inside diameter of 20 cm, and outside diameter 30 cm. The lagging is 10 cm thick and has a thermal conductivity ki of 0.1 W/m K. The thermal conductivity of the pipe wall kp is 80 W/m K, the steam is at 300oC and ambient surrounding air is at 20 oC. You may assume the pipe is sufficiently long with hin = 40 W/m2 K, and hout = 16 W/m2 K
Two parts and label (A) & (B) Solve carefully! Question : The roof of a car in a parking lot absorbs a solar radiant flux of 600 W/m2, while the underside is perfectly insulated. The convection coefficient between the roof and the ambient air is 15 W/m2.K and the roof’s surface emissivity is 0.5. If the ambient air temperature is 25C, answer the following questions: PART (A) Neglecting radiation heat transfer, find the temperature of the roof under steady state conditions. Part ( B) Neglecting convective heat transfer, find the steady state temperature of the roof [Tsur =0]?
Estimate the unit thermal resistance for a vertical 1.5 in. (40 mm) air space. The air space is near the inside surface of a wall of a heated space that has a large thermal resistance near the outside surface. The outdoor temperature is 10 F (-12 C). Assume nonreflective surfaces.
A spherical tank made up of stainless steel is to be used for storage of oil at 150°Cthat is needed for heating purposes in a plant. It is decided to insulate the tank in order todecrease the heat loss to the surroundings, which is at 20°C having heat transfer coefficient of 25W/m2.K. The heat loss is compensated by the heating resistance inside of the tank. There are twotypes of insulating material present at this plant each is enough for covering the tank with onlyone layer. These are;Type 1: k=0.1 W/m.K thickness=5cmType 2: k=0.25 W/m.K thickness=5cmAn engineer is thinking about the most efficient way of covering the tank in order to minimize theheat loss. Please help him for this purpose. Is it more efficient to cover type 2 over type 1 or type1 over type 2? Explain why?
i need the answer quickly
The lining of box-type fumace is made up of a refractory layer and steel plate as shown in the figure. Steady state temperature at the surface of the refractory is 1273 K and that at the outer steel surface is 473 K. If the steady state heat flux through the refractory-steel plate composite is 1600 W/m², and heat flow is along x-direction only, the thermal contact resistance (m² K/W) between refractory and steel is_ steel Refractory 1273K Furnace 473K Ambient Given data: Thermal conductivity of refractory = 1.2 W/m-K Thickness of refractory lining = 80mm Thermal conductivity of steel = 32 W/mK Thickness of steel plate = 4mm
A furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal conductivities of 1.65, k and 9. W/m K respectively. The inside is exposed to gases at 1250 ˚C with convection of 25 W/m2K, and the inside surface is at 1100 ˚C, the outside surface air at 25 ˚C with convection of 12 W/m2K. Determine the temperatures of the mid-inner surface in 0C to 1 d.p.?