Q. 5A full hydrodynamic bearing having journal diameter of 60 mm and radial load of 1000 N. If journal speed is 1500 rpm and length of thejournal is 25 mm. The standard value of radial clearance is 25 um, what will be the flow of lubricant if flow variable is given by 4.29.Have any Doubt ?A1009 mm3/secB1510 mm3/sec

Given DataW=1000ND=60mmR=30mmN=1500 rpm

A full hydrodynamic bearing having journal diameter of 60 mm and radial load of 1000 N. If journal speed is 1500 rpm and length of th ournal is 25 mm. The standard value of radial clearance is 25 um, what will be the flow of lubricant if flow variable is given by 4.29. Have any Doubt ?

A full hydrodynamic bearing having journal diameter of 60 mm and radial load of 1000 N. If journal speed is 1500 rpm and length of th ournal is 25 mm. The standard value of radial clearance is 25 um, what will be the flow of lubricant if flow variable is given by 4.29. Have any Doubt ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 2 A pressure-fed bearing has a joumal diameter of 55.00 mm with a umilateral tolerance of -0.05 mm. The bushing bore diameter is 50.084 mm with a unilateral tolerance of 0.10 mm. The length of the bushmg is 55 mm. Its central annular groove is 5 mm wide and is fed by SAE 30 oil is 55°C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 10 EN. The sump ca dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the minimum film thickness and average temperature. Given the film temperature is 85° c Attach File Browse My Computer QUE STION 3
I need the answer at 20 minute
For base case: N= 3500 rpm. D = 8 and 3/8 inch, Q = 400gpm, H = 280 ft, P = 41 hp, %3D Determine new Q. H, and P for |(a) when diameter is changed to 7" and speed is constant (b) when speed changes to 1750 rpm and diameter is constant (base case diameter)
Problem 6 The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 75 mm wide. The coefficient of friction is 0.20. The maximum lining interface pressure is pV=1.5 MPa.m/s. (a) Find the brake torque, necessary force P, and steady-state power. (b) Complete the free-body diagram of the drum. Find the bearing radial load that a pair of straddle-mounted bearings would have to carry. 75 mm- -250 mm-
How much horsepower is delivered by a block brake having a drum 120 mm in diameter and a 400 mm brake arm length. The pivot point is 40 mm below the point of tangency and 80mm horizontally between the drum and the shoe. The applied load for clockwise rotation is 24,767N when the drum rotates at 300 rpm. Assume a coefficient of friction of 0.25.
Wear rate of a truck tyre under an average load of 53 tonnes was 0.6m per kilometre of travel when it was just rolling, however, it increased to 5um when it was slipping under a stopping brake on a downhill slope having the grade g = 17%. Calculate the tyre working life in terms of number of kilometres travelled for both (1) rolling and (il) slipping case, if the maximum tyre thread depth was 21 mm. Calculate the stopping brake distance for the case of (iii) rolling and (iv) slipping, when the truck started braking at the speed of 52km/hr.
i need the answer quickly
A pressure-fed bearing has a journal diameter of 63.00 mm with a unilateral tolerance of -0.05 mm. The bushing bore diameter is 63 084 mm with a unilateral tolerance of 0.010 mm. The length of the bushıng is 58.00 mm. Its central annular groove is 8.00 mm wide and is fed by SAE 30 oil is 55°C at 195 kPa supply gauge presaure. The journal speed is 2880 revimin carrying a load of 20 kN. The sump can dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the average temperature Given the film temperature is 95°C
i need the answer quickly
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?
!