A frustum cone tank is initially filled with water as R= 2w shown in figure. After that, the water drains through a hole of radius (r=0.05 m) is located at the bottom of tank. 1- Find the depth of water at any time (y(t)). 2- compute the time required to drain half volume of water in the tank. where R,= w w = 2m g = 10 m/s?

A frustum cone tank is initially filled with water as R= 2w shown in figure. After that, the water drains through a hole of radius (r=0.05 m) is located at the bottom of tank. 1- Find the depth of water at any time (y(t)). 2- compute the time required to drain half volume of water in the tank. where R,= w w = 2m g = 10 m/s?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As shown in the figure, a pump draws water from reservoir A (EI 25m) and lifts it to reservoir B (El 60m). The loss of head from A to 1 is 2 times the velocity head in the 200 mm pipe and the loss of head from 2 to B is 10 times the velocity head in the 150 mm pipe. Calculate the pressure head at point 1 when the discharge is 0.030 m³/s. Round off your answer to one decimal place. E1 25 7 Pl Answer: = 4 200 mm 2 m 150minh EL O El 60 B
Find the depth of the water in the tank, H, and the manometer reading, h, if the hydrostatic force on the circular plug is 25 N. Take the specific weight of the water as γwater = 9810 N/m3 and the specific gravity of mercury Sm = 13.56
Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is 1.85 × 105 Pa and 1.10 x 105 Pa. The radius of the pipe at points 1 and 2 respectively is 3.20 cm and 1.40 cm. If the vertical distance between points 1 and 2 is 2.75 m, determine the following. (a) speed of flow at point 1 m/s (b) speed of flow at point 2 m/s (c) volume flow rate of the fluid through the pipe m³/s P₂ y
A pump system is used to move water at a flow rate of 30 L/s from a lower to a higher reservoir in a city with an elevation of 1000 m above sea level. The system is shown schematically in the figure below, with ∆?=30 m. Both the suction and delivery pipes have a diameter of 150 mm and an absolute roughness of 0.3 mm. The lengths of the suction and delivery pipes are 6 and 500 m respectively. Ignore local losses and assume a temperature of 15 °C. a)Develop a mathematical expression for the system curve (i.e. the pumping head required as a function of the system flow rate) from basic principles. Name all mechanics principles implemented. b)Calculate the required pump working point. What is the flow regime of the pipe flow. c)What power does the pump add to the water in the system?
Bernoulli's theorem demonstration: 5 L of Water is flowing through a venturimeter in 6.5s. What is the pressure difference (p1- P2) (in kPa) for this flow? D=32 mm, d=23 mm, g = 9.8 m/s² and y=9.8 kN/m³
A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and 1m from the bottom respectively. Both orifices are 100 mm diameter with C=0.607. Determine the: show complete solution a. How long will it take to lower the water at tank by 2 m in seconds?b. How long will it take for the water surface to be at the same level as the upper orifice in seconds?
(Multiple pipes) The three tanks shown in the figure below are connected by pipes with friction factors of 0.03 for each pipe. Determine the water velocity in each pipe. Neglect minor losses. Elevation = 857 ft Elevation = 822 ft D = 1.1 ft D = 1.0 ft l = 700 ft l = 800 ft (1) (A) V₁ = i (B) V₂ = i (C) V3 = i (3) D = 1.2 ft € = 600 ft (2) ft/s ft/s ft/s Elevation = 793 ft
A 1.5m square tank, 3m tall is drained by a 25mm-diameter orifice located at its bottom. If the tank is initially filled with water, how deep is the water in the tank after 45 minutes? Assume C=0.62
3. IN THE FIGURE SHOWN, THE 50-METER PIPE IS 60 MM IN DIAMETER. THE FLUID FLOWING HAS MASS DENSITY OF 920 KG/CU.METER AND DYNAMIC VISCOSITY OF 0.29 PA-S. THE PRESSURE IN THE ENCLOSED TANK IS 200 KPA GAGE. DETERMINE THE FOLLOWING(ƒ =0.0225). A. THE AMOUNT AND DIRECTION OF FLOW B. THE VELOCITY OF FLOW IN THE PIPE. C. THE REYNOLDS NUMBER OF THE FLOW H= 12 m L=50 m
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend is installed in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the x and y for components of the thrust block to hold the pipe bend. Horizontal Thrust block 30° 50° Open end Ø80 mm Ø 160 mm Figure 3 Cs Scanned with CamScanner Vertical
Two pipes A and B are connected in parallel between two points M and N as shown in figure. Pipe A is 80 mm diameter, 900 m long and its friction factor is 0.015. Pipe B is of 100 mm diameter, 700 m long and its friction factor is 0.018. A total discharge of 0.030 m³/s is entering the parallel pipes through the division at M. Calculate the discharge in the two pipes A and B. M = 0.015 A fA 80 mm dia, 900 m 100 mm dia, 700 m B fB = = 0.018 N
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.