A four-link mechanism is subjected to the following external forces determine the shaft torque T2 on the input link AB for static equilibrium of the mechanism. Also find the forces on the bearings A. B. C and D. AB = 500 mm, BC 660 mm, CD 560 mm, AD =1000 mm F2= 80 N, F3= 144 N, F4= 60N %3D - 297- Bp 58 Draw the mechanism diagram with a suitable scale (say, SM = 0.1 mm/mm) as shown 325 373 73.5 60 (mm)

A four-link mechanism is subjected to the following external forces determine the shaft torque T2 on the input link AB for static equilibrium of the mechanism. Also find the forces on the bearings A. B. C and D. AB = 500 mm, BC 660 mm, CD 560 mm, AD =1000 mm F2= 80 N, F3= 144 N, F4= 60N %3D - 297- Bp 58 Draw the mechanism diagram with a suitable scale (say, SM = 0.1 mm/mm) as shown 325 373 73.5 60 (mm)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

20 kN.m 2 kN/m A- CO 2m 4m 2m e reaction at hinge B is elect the correct response: 23.0 kN 10.0 kN 29.0 kN 14.0 kN
Pravinbhai
spring is to be inserted with an initial compression to produce a force equal to 125 N between the right-hand end of the lever and the stop. When the maximum force at A reaches to a value of 200 N, the end of the lever moves downward by 25 mm. assuming a spring index 8 determine the following parameters: 1. Spring rate 2. Size of the wire 3. Outside diameter of the spring 4. Number of active coils, and 5. Free length, assuming squared and ground ends Note: the allowable shear stress may be taken as 420 MPa, and G = 80 GPa. Hint: Ans. 0.33 N/mm: 3.4 mm; 27.2 mm; 77 mm - 200 mm - 200 mm Lever Stop -Spring
Thank you And please kindly write legibly because I'm having a hard time reading, guessing, and understanding the handwriting of different experts recently. Thanks Please refer to the photo below. SUBJECT: Statics of Rigid Bodies EQUILIBRIUM
The spring clamping force Fg = 2 N. The contact pressure force FA and the joint forces FB at the jump piece 1 should be determined for the toggle mechanism with a straight guide shown in figure. C 26 mm B 2 10 mm A 1 8 mm 7 mm D 10 mm 15 mm 10 mm
Draw the free body diagram (FBD) of the bolt of the mechanical jack in the locked state shown in the figure.
From the figure below, choose the correct answer of the following 6 kN 5 kN 3kN. 30° 5. 0.2 m 4 В А -2 m 4 m 2 m 3.
Please sir give me answer immediately
A crank shaft is operated as shown in the figure. A load F1 = 9.73 N is applied and the operator %3D dz applies a load P to counter. The system is in equilibrium and all of the bearings are perfectly dz aligned such that they do not produce moments on the rotating crank. The geometry is given by, w = 7.31 [m), dl = 9.69 m], d2 = 7.57 m). 6.14 (m), d5 = 3.7 (m), %3D d1 d3 = 9.87 (m), d4 %3D F2 and h1 4.4 (m), find the following: %3D F1 Part 1. Express the reaction forces exerted on the bar by the journal bearing at point B. Use the coordinate system shown in the diagram 10 5% 100% Submit [N] Part 2. Express the reaction forces exerted on the bar by the journal bearing at Point A. Use the coordinate system shown in the diagram. 5% 100% 10 Submit [N]
For the mechanism shown in the figure, determine the torque TA required at crank AB to maintain static equilibrium of a 250-lb force FT acting on link 6 (E) when theta = -330 grades. The Dimensions are: h = 16, d = 20 and AB = 8 (inch units). d ΤΑ & c
pls answer thank u!8
5. In the mechanism shown in the figure, a-150mm,b-155mm,c%3D160mm,d%3D100mm, e=350mm. Analysis whether the mechanism has the quick-return motion when AB acts as the driving link and slider E acts as the driven link (If it has, redraw a figure to find the coefficient of travel speed variation K)? Is there a change if CD acts as the driving link? Explain that using the graphical method. Bo e E D