Nn.147.Subject :- Mechanical engineering A four-bar mechanism is working on horizontal plane. The second link length is 0,4 m and makes an angle of 0-41 degrees with the vertical line as shown in figure.Find the torque (T) in Nm must be applied to link 2 to keep the mechanism in equilibrium against a F=178 N force acting at E on the link 3 upward (along positive y-axis) direction.Allowable tolerance for your answer of this question is relatively 3 percent. So, work precisely and clear while solving it. Do not enter any UNIT.(If the direction of the torque is CCW, just enter the value of it without any sign. If it has CW direction, enter "-" sign "negative sign" before the value such as "- 12,12")ABTCAB-COAD=BC=0.7 mBE=ECt

Given that: AB = CD = 0.4 m AD = BC = 0.7 m BE = EC θ = 41° F = 178 N To find: T4

A four-bar mechanism is working on horizontal plane. The second link length is 0,4 m and makes an angle of 0-41 degrees with the vertical line as show Find the torque (T) in Nm must be applied to link 2 to keep the mechanism in equilibrium against a F=178 N force acting at E on the link 3 upward (along axis) direction. Allowable tolerance for your answer of this question is relatively 3 percent. So, work precisely and clear while solving it. Do not enter any UNIT. (If the direction of the torque is CCW, just enter the value of it without any sign. If it has CW direction, enter "-" sign "negative sign" before the value such

A four-bar mechanism is working on horizontal plane. The second link length is 0,4 m and makes an angle of 0-41 degrees with the vertical line as show Find the torque (T) in Nm must be applied to link 2 to keep the mechanism in equilibrium against a F=178 N force acting at E on the link 3 upward (along axis) direction. Allowable tolerance for your answer of this question is relatively 3 percent. So, work precisely and clear while solving it. Do not enter any UNIT. (If the direction of the torque is CCW, just enter the value of it without any sign. If it has CW direction, enter "-" sign "negative sign" before the value such

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.20P: A magnesium-alloy wire of diameter d = 4mm and length L rotates inside a flexible tube in order to...

See similar textbooks

Similar questions

Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
Repeat Problem 6.4-14 but use the configuration of channel shapes and loading shown in the figure. Use P = 250 N.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?
Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
Repeat 1.3-9 but use the method of sections go find member forces in AC and BD.
Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.
A cable and pulley system in the figure part a supports a cage of a mass 300 kg at B. Assume that this includes the mass of the cables as well. The thickness or each of the three steel pulleys is t = 40 mm. The pin diameters are dPA= 25 mm, dB= 30 mm. and dc= 22 mm (see figure part a and part b). (a) Find expressions for the resultant forces acting on the pulleys at A, B. and C in terms of cubic tension T. (b) What is the maximum weight W that can be added to the cage at B based on the following allowable stresses? Shear stress in the pins is 50 MPa; bearing stress between the pin and the pulley is 110 MPa.
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
Repeat Problem 10.4-41 for the loading shown in the figure.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
The device shown in the figure consists of a prismatic rigid pointer ABC supported by a uniform translational spring of stiffness k = 950 N/m. The spring is positioned a distance P = 165 nun from the pinned end A of the pointer. The device is adjusted so that, when there is no load P, the pointer reads zero on the angular scale. (a) If the load P = 11 N, al what distance .v should the load be placed so that the pointer will read ?? = 2.5° on the scale (see figure part a)? (b) Repeal part (a) if a rotational spring E1= kb-6 is added al A (see figure part b). (c) Lel.x = 7b/8.What is P maxif 0 cannot exceed 2"? Include spring krin your analysis. (d) Now, if the weight of the pointer ABC is known to be W =3N and the weight or the spring is Ws= 2.75 N, what initial angular position (Left in degrees) of the pointer will result in a zero reading on the angular scale once the pointer is released from rest? Assume P = kr=0. (e) If the pointer is rotated lo a vertical position (see figure part c), find the required load P applied at mid-height of the pointer that will result in a pointer reading of 0 = 2.5" on the scale. Consider the weight of the pointer W. in your analysis.