Using the cut method, draw the shear and moment diagrams for the beam, and calculate the shear and moment throughout the beam as functions of x. 2 N/m 6m- 10 N 8 N 40 Nm

Q: What is elongation testing?

A: Elongation testing is a measure of far stretching of a sample before it breaks. The result is…

Q: How does the LRFD method of design react on the load and strength of the material?

A: LFRD means Load and resistance design factor is a method of design of steel structures and…

Q: Why do the Ductile materials fail in shear?

A: Ductile materials are the materials which goes plastic deformation before the fracture. When any…

Q: scuss the concept of stresses? State the properties could be drawn from the stress strain diagrams

A: when load is applied on a member , by nature it will try to deform the member. the material will try…

Q: Give a formula that can be used to determine a been allowance for a soft material

A: There is some typing mistake. It must be "bend allowance", not "been allowance".

Q: What happens if the principal stresses at a critical point in the material?

A: First, define the critical point. Critical points are those points in the given plane where the…

Q: Process used to improve fatigue resistance of the metal by setting up compressive stresses in its…

A: Cold Peening or Shot Peening: It is a cold work process used to prevent parts from fatigue and…

Q: 1. What is the difference between direct and shear stress?

A:

Q: Table 3 shows the fatigue data for a ductile cast iron to be used for an automobile axle that…

A: Given Data for ductile Cast iron Stress Ampitude (Mpa) Cycles to failure 740 1*101 604.8…

Q: Define the term Stress Concentrations?

A: Stress concentration is a location in a member under load where the magnitude of stress is…

Q: creep occurs when vacancies in the material migrate towards grain boundaries that are parallel to…

A: Here question is about creep phenomena, we have to choose whether the given statement is true or…

Q: What is the slenderness ratio?

A:

Q: Give an example of the Absolute Maximum Shear Strain?

A:

Q: List 10 materials of a windmill.

A: Wind mill: It is mechanical device which convert the kinetic energy of the air into the mechanical…

Q: What is creep strength?

A: Creep is the phenomena of deformation of a body which is time-dependent. It occurs when a load is…

Q: How does point defect affects the property of a material?

A: To find : How does point defect affects the property of a material

Q: Aluminium and copper wires can be made by cold drawing process. Select one: O True O False

A: True

Q: -0.749 diom -0.561 diam -24 UNF-2A-

A: Based on the information provided, there are two components that failed: the M24 engine mounting…

Q: What important quantity (or quantities) can be determined by measuring striation spacing?

A: Striation Spacing: Striation Spacings are the marks that are produced at the mating surfaces of the…

Q: Define rate of linear deformation?with unit

A:

Q: Using the Griffith criterion, what is the strength of a piece of soda-lime-silica glass that…

A: The strength of a piece of soda-lime-silica glass is 102 MPa.

Q: If the moduli of rigidity and elasticity of a material are 15,000 ksi and 40,000 ksi, respectively,…

A:

Q: What is the tensile strength of a metal if its endurance limit is 84675 psi?

A: Given that the endurance limit of the material is 84575 psi. Write the endurance limit formula,…

Q: c) Calculate ore grade when (12 - Pn) t (tonnes) of copper is extractable from a copper ore mine…

A: Given questions are related to material science.

Q: Define what is tensile strength? short definition 2-3. sentences.

A: Questions: define what is tensile strength?

Q: Stresses applied to plastically deform the metal are usually compressive. O F

A: To get the material plastically deformed it is necessary that stresses are applied beyond the…

Q: Which of the four major material groups has the lowest thermal conductivity?

A: The four major material groups are :Metals, Non metallic organics, organics and polymers. Among…

Q: The collar A, having a mass of 0.75 kg is attached to a spring having a stiffness of k = 260 N/m.…

A: Given data  Mass of collar = 0.75 kg Spring constant = 260 N/m Find the speed of collar and normal…

Q: What is true stress and true strain?

A: To define: True stress True strain Stress: It is defined as the internal resistance developed at a…

Q: What is the linear variation in the shear strain?

A: The change in shape obtained due to shear stress is defined by shear strain.

Q: Describe distributed loadings?

A: Distributed load is a load applied across a length or area instead of at one point on a beam. If we…

Q: What is shear strength & how is it calculated?

A: There are no standard values published in the books for the shear strength. In some cases we take 60…

Q: Discussion : 1- Through the results of the experiment and graphs, what is the effect of the…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Q/Define the stiffness? Discuss the criteria for selection of materials for stiffness

A: The resistance to a force that might otherwise cause a part to bend is known as stiffness. Many…

Q: Process used to improve fatigue resistance of the metal by setting up compressive stresses in its…

A:

Q: List 3 of the design methods that can be applied to avoid the occurrence of fatigue

A: Fatigue is the beginning and spread of fractures in a material as a result of cyclic stress,…

Q: What is Residual Stress?

A: Whenever a body is deformed beyond the elastic limit it is unable to regain its initial shape. Due…

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.