A footing is uniformly loaded with q = 100 kN/m² as shown in the figure. Compute the vertical stress increments under Points A, B, and C at z = 10 m. 13.5 m A 7.0 m Footing 12 m B (Plane view) 6.0 m

Q: How important is geogoly in structural engineering?

A: Geology is the science that studies the earth's origins, structure, composition, and history.…

Q: Determine radius of mohr circle 9 MPa 4 MPa 6 MPa

A:

Q: Describe the following structural geology and mapping terms   folds faults engineering problems…

A: Solution: Folds: The folds are generally the waves and undulation that are within the stratified…

Q: Surveys are carried out to define land ownership and boundaries O Cadastral Surveying Topographical…

A: Surveys are carried out to define land ownership and boundaries--> Cadastral Surveying

Q: A Find by Section Method and Join Method: 3 B Hawe Bridge 50 3′ E D 50 3 F G 50 3' H A

A: To find the member forces in the given truss by both methods.

Q: 2. A hemispherical roof dome is subjected to a snow load ps. Develop the expressions Ps a and 0e Ps…

A:

Q: Show that: Ble -= $a n

A:

Q: Angle of elevation and depression are measured from the (horizontal/vertical)

A:

Q: What is the use of geosynthetic fabrics

A: Geosynthetics can be defined as it is a synthetic product, which is used to support the terrain. It…

Q: Construct a dot plot for the asphalt data30 75 79 80 80 105 126 138 149 179 179 191 223 232 232 236…

A: Dot plot is used to represent a quantitative data and each dot in the plot represents a value. For…

Q: Q2: Given the following planar manipulator find the following a) °T2 b) 2R, c) The location of 02…

A: Planar manipulator: A manipulator is called a planar manipulator if all the moving links move in…

Q: Explain about Geotechnical Measurements ?

A: Geo-technical measurement:   Geo- technical measurement are the measurement which performed to know…

Q: itemize the geotechnical engineering problems related to water in sections

A: Water can cause a range of geotechnical engineering problems and it is important for engineers to…

Q: calculate the linear misclosve

A: Fore bearing is the bearing of a given line in the direction of survey and back bearing is the…

Q: Explain with sketches about the manufacturing and applications of (i) Geomembranes and (ii)…

A: Manufacturing Geomembrane Type Resin Plasticizer Filler Carbon Black or Pigment Additives HDPE…

Q: locate a missing point on the ground: a. You need at least three reference points b. You need at…

A: Given To locate a missing point on the ground:

Q: Three level Section is the Figure

A: C is three level section

Q: A surface depression typically along the wheel paths of a road. Blank 1

A: RUTS are the surface depression that are developed typically along the wheel paths of a road.

Q: Benchmark A has an elevation of 437.596 m. What are the most probable values for B, C, D?

A: Solution:

Q: FIND THE LENGTH OF THE DIVIDING LINE DP. THANK YOU. (THIS SUBJECT IS SURVEYING)

A:

Q: Define Normalized CPT Parameters

A: Cone penetration testing (CPT) is used to identify the soil type. In this test a cone penetrometer…

Q: Discuss the importance of accuracy and precision in surveying measurements

A: In surveying, accuracy, and precision are key ideas that guarantee the dependability and caliber of…

Q: What is the type of traverse shown in the picture? (select all that apply) Az Mk (a)

A: Given that:

Q: Identify and describe the following surface analysis techniques AES, AFM, EDS, FIB, FTIR, SEM, TEM,…

A: Atomic Force Microscopy (AFM) Atomic Force Microscopy (AFM) is an analysis that quantifies surface…

Q: . Enlist major three sources of errors in

A: Three major sources of errors in surveying are: 1. Instrumental 2. Personal 3. Natural

Q: 1. Using Simpson's one third rule, calculate the area of the plot shown in figure below. if the…

A:

Q: Define fundamental volume-related geotechnical engineering properties

A:

Q: Q2: From the following excerpt of field notes, plot the cross section on graph paper and superimpose…

A: We have to determine the area by coordinate method as per the given data like slope 3:1 and subgrade…

Q: Complete the notes, find the elevation of point A and state the error in the network. Determine the…

A: HI= Elevation +BS Elevation= HI-FS

Q: Give some examples of Geotechnical Instrumentation And Monitoring Companies ?

A: As the infrastructure developed, then constriction instrument is also increases in large number.…

Q: FB AB = S 78° 17' E BB AB = N 79° 56' W FB BC = S 8° 34'E BB BC = N 7° 07' W FB CD = S 37° 17' W вв…

A:

Q: represent

A: Standard penetration test(SPT) is most commonly used in-situ test, especially for cohesionless soils…

Q: Find Inside Area of these Rooms and inside Length of the walls 10.0 3.2 4,5- R0.7 R0,6 A1 2,1 A4 2.2…

A: To Determine Inside Area of these Rooms and inside Length of the walls.

Q: ● Add the following angles: 25°54'13" + 100°05'25" 225°54'28" + 67°30'55" • Subtract the following…

A:

Q: 3. (x² – 3y²)dx + 2xdy = 0 | 4. xydy = (x² – 2y²)dx %3D

A:

Q: What is the Protection functions in Geosynthetics?

A: Let’s first understand what is “Geosynthetics”: Plastic products that are made predominately from…

Q: If weight of angles A & B is a AABC is W, the ratio of weight of angle C to weight of A is (a) 1 - 8…

A:

Q: Geotechnical Engineering How important Atterberg Limits?

A: Introduction: Atterberg limits are the methods to measure the water contents in the soil. It is also…

Q: C = 52° 29' a = 70° 20' 50" c= 51° 41' Find A.

A: Given data: C = 52° 29' a = 70° 20' 50" c= 51° 41' Find A.