A fluid flowing in a pipe 30 cm in diameter has a uniform velocity of 4 m/s. The pressure at the center of the pipe is 40 kPa, and the elevation of the pipe's centerline above an assumed is 4.5 m. Compute the total energy per unit weight of the flowing fluid if it is [a] oil, sg = 0.80; and (b) gas, y %D = 8.50 N/m3

A fluid flowing in a pipe 30 cm in diameter has a uniform velocity of 4 m/s. The pressure at the center of the pipe is 40 kPa, and the elevation of the pipe's centerline above an assumed is 4.5 m. Compute the total energy per unit weight of the flowing fluid if it is [a] oil, sg = 0.80; and (b) gas, y %D = 8.50 N/m3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve last three parts where density of fluid is 900kg/m3
What pressure, p₁, is needed to produce a flowrate of 0.09 ft3/s from the tank shown in the figure below? Assume d = 0.071 ft. P1 = Mi ! psi Air P1 Gasoline diameter d→ Salt water SG = 1.1 2.0 ft 3.6 ft
(a) The speed of an aircraft flying at an altitude of 11 km is measured by a pitot-staticprobe. If the differential pressure reading is 12.9 kPa, determine the speed of theaircraft in km/h. Take the density of air to be 0.4135 kg/m3
6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and has coefficients of velocity and discharge of 0.98 and 0.96, respectively. The nozzle is supplied from a 60cm pipe in which the water approached the nozzle with a total head of 330m. Compute the following: a. Energy per second delivered by the jet to the turbine. b. Energy measured in hp lost in passing through the nozzle.
Where did this 101.3 over 76 coming from? Its not on the given. Here is the picture.
Please answer, hydraulics.
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
A pump is used to move water from a lake to a large industrial tank, which is 30 m higher than the reservoir surface through a pipe 300 m long at a flow rate of 1 m³/s. The pipes are uniform and having a diameter of 60 cm. The friction factor in the pipe is given as f = 0.05. The vapour pressure of water can be taken as 4780 kPa. Calculate (a) Velocity of water through the pipe (b) Head loss in the pipe (c) Required head by the pump (d) Power supplied, in kW if pump efficiency is 75% (e) Available NPSH for the pump installation
Question Certain fluid parameters are provided The inner cylinder, with a diameter of 20 cm, remains stationary, while the outer cylinder, with a diameter of 21 cm, holds the liquid up to a height of 30 cm. There is a 1.0 cm gap between the bottom of the two cylinders. By rotating the outer cylinder at a speed of 200 revolutions per minute (r.p.m.), the torsion meter attached to the inner cylinder registers a torque of 6.0 N-m. a. Determine the toque on the bottom in terms of b. Determine the toque on the surface in terms of ..... c. Determine method the viscosity of a liquid (N-sec/m^2)(Ans up to 2 decimal) μ (Ans up to 4 decimal) ..u.(Ans up to 4 decimal) using the rotating cylinder
A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the water when a piston applies a pressure of 33 MPa. m³
subject: hydraulics. 3 decimal places. p.s with solution