A flow of 2 kg/s completely dry air at T1, 100 kPa is cooled down to 10°C by spraying liquid water at 10°C, 100 kPa into it so it becomes saturated moist air at 10°C. The process is steady-state with no external heat transfer or work. Find the exit moist air humidity ratio and the flow rate of liquid water. Find also the dry air inlet temperature T1.

A flow of 2 kg/s completely dry air at T1, 100 kPa is cooled down to 10°C by spraying liquid water at 10°C, 100 kPa into it so it becomes saturated moist air at 10°C. The process is steady-state with no external heat transfer or work. Find the exit moist air humidity ratio and the flow rate of liquid water. Find also the dry air inlet temperature T1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air at 1200K, 800 kPa expands in a polytropic process with n = 1.33 to a pressure of 300 kPa. Find out the final temperature of the air and the specific work output?
An insulated chamber containing 2 L of saturated liquid water at 300 kPa constant pressure. There is a piston-cylinder assembly. One with an electric heater inside the cylinder There is a mixer. Then the water is mixed by the mixer for a while. s mixed, as well as connected to 220 volt electrici supply and 8 A current through neated by the passing heater. This state change at constant pressure 500 kJ of work is done by the mixer. Meanwhile, iquid 90 percent by mass evaporates. a) Plot the state change on T-v and P-v diagrams, paying attention to saturation lines. D) Calculate the operating time of the electric heate
Water vapor in a steady-flow adiabatic turbine 9 MPa pressure and 600 ° C temperature, with 20 kPa pressure and 85 percent dryness comes out. Ignoring kinetic and potential energy changes, the turbine's 8 Calculate the required mass flow to generate MW power.
Find the total enthalpy of 1.4 kg of steam that is at 350 kPa with a 0.36 quality?
I have been working on this problem for a while but I need to figure out how to get the specific enthalpy when the refridgerant exits the system to find the mass flow rate of when the refridgerant exits the system but I don't know how to do this
?????
Thermodynamic question How to draw the T-s diagram for the his problem? A volume flow of air at 500K, 20bar passes in a long pipe through a temperature reservoir that is kept at a temperature of 1000°C. The air exits at 1000K and 1.8 MPa. Consider air as ideal gas with variable specific heats, ? = 0.287 kJ/kg-K
From a state defined 300 psia, 100 cu. ft and 245 deg. F, Helium undergoes an Isentropic process to 0.5 psig. Find: a. V2 and T2 b. Change in Enthalpy and Internal Energy c. Heat and Change in Entropy.
Q11
8000 m3 Humid air at 35 ° C dry bulb and 25 ° C wet bulb temperature at / h flow rate It is passed through a cooling coil until it becomes saturated at 17 ° C. This process Some of the moisture in the air condenses during the process and is taken out at 13 ° C. Accordingly, find the amount of heat drawn from the air and the amount of condensed water.
Hand written plzz Is the entropy constant during the polytropic process?
Atmospheric air at 15 °C, relative humidity 10%, is too hot and also too dry. An air conditioner must deliver air at 21 °C and 50% humidity relative in the amount of 3600m³/h. Propose a scheme to achieve this, find the amount of liquid (at 20°C) required to be added or removed and any transfer of heat.