Helium at 100 kPa, 500 K is in a piston/cylinder setup and is compressed to a final pressure of 800 kPa. Consider helium as an ideal gas with constant specific heat capacities. Find the final temperature and the specific work if the above process is (i) reversible adiabatic (ii) reversible isothermal

Helium at 100 kPa, 500 K is in a piston/cylinder setup and is compressed to a final pressure of 800 kPa. Consider helium as an ideal gas with constant specific heat capacities. Find the final temperature and the specific work if the above process is (i) reversible adiabatic (ii) reversible isothermal

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An insulated chamber containing 2 L of saturated liquid water at 300 kPa constant pressure. There is a piston-cylinder assembly. One with an electric heater inside the cylinder There is a mixer. Then the water is mixed by the mixer for a while. s mixed, as well as connected to 220 volt electrici supply and 8 A current through neated by the passing heater. This state change at constant pressure 500 kJ of work is done by the mixer. Meanwhile, iquid 90 percent by mass evaporates. a) Plot the state change on T-v and P-v diagrams, paying attention to saturation lines. D) Calculate the operating time of the electric heate
Initially, the air with 180 kPa pressure and a volume of 1 m3 is heated up to 660 oC. Mass of air 68 kg calculate the entropy change that occurs during this heating process (Ideal gas for air You can use the equations).
Air at 1000 C°, 1.0 MPa expands in a polytropic process with n = 1.3 to a pressure of 250 kPa. Find 1- the final temperature 2- the specific work output
3. An empty 100-L tank is connected to a line flowing air (an ideal gas) at 300 K and 6 MPa. The valve is opened and the air starts to flow into the tank. The valve is closed when the pressure inside reaches 5 MPa. This filling process occurs so fast that it can be assumed as adiabatic (i.e., no heat transfer). At the point when the valve is closed, what is the temperature and mass of air inside the tank?
Steam expands isentropically from 2 MPa and 375 o C to a final temperature of 95 o C.Find the final quality and the work for a non-flow and steady flow processes.
Find the total enthalpy of 1.4 kg of steam that is at 350 kPa with a 0.36 quality?
Please don't provide handwritten solution ....
In a frictionless piston-cylinder system, 5 kg of R-134a superheated steam at 1000 kPa and 140It is in ˚C. Fixed up to 25% dryness degree of system R134apressure cooled. Find the work done in the system. Show the process in the P-v diagram
During an isentropic process of 3 lb/sec of air, the temperature increases from 50 deg F to 290 deg F. Find the work for a steady flow process.
One kg of steam undergoes a reversible isothermal process from 20 bar and 250°C, to a of 30 bar. Find the heat flow stating if it is supplied or rejected. pressure
A piston with water vapor at a pressure of 300 kPa and a temperature of 175 oC. 20 kg of fluid is compressed up to 950 kPa pressure in the cylinder arrangement. Piston cylinder device to a heat well at 80 oC in order to keep the temperature of the water in it constant. The heat generated during compression is discarded. a) What phase is the water in the first case? In the last case, what phase is the water in? b) Find the entropy change in water by the process. c) From the cylinder, assuming that the process is a reversible process at constant temperature. Calculate the amount of heat absorbed. d) Find the entropy change of the heat well. e) Consider the total entropy change including the piston-cylinder mechanism and the heat indicate whether the transaction is reversible or irreversible when received. f) T (° C) -s (kJ / kgK) and P (Pa) - by specifying the state change saturation curves and values Show in (m³ / kg) diagrams.
6. Steam expands isentropically from 2 MPa and 375 °C to a final temperature of 95 °C. Find the final quality and the work for a non-flow and steady flow processes.