A flat steel plate is of trapezoidal form and uniform thickness of 10mm. The plate tapers uniformly from a width of 150mm to 100 mm over a length of 500mm. Determine the elongation of the plate under an axial pull of 100 KN. Take E= 200 KN/mm² B₁ 100 KN 100 mm 8x 500 mm 150 mm B₂ 100KN

A flat steel plate is of trapezoidal form and uniform thickness of 10mm. The plate tapers uniformly from a width of 150mm to 100 mm over a length of 500mm. Determine the elongation of the plate under an axial pull of 100 KN. Take E= 200 KN/mm² B₁ 100 KN 100 mm 8x 500 mm 150 mm B₂ 100KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2 The series of bars shown have their diameters from left to right decreasing by 3 mm, and lengths increasing correspondingly by 0.3 m. If the leftmost member has a diameter and length of 28 mm, 1.8 m, respectively, determine the nodal displacements, member forces and the value of P if the node where P acts undergoes a rightward displacement of 4.5 mm. E=180 GPa for all members. Use your calculator. 90 N/mm 45 N/mm 60 N/mm 30 KN -50 KN
The rigid bar ABC is supported by a pin at A and a steel rod at B. The stress in the steel rod is limited to 55 ksi and the vertical movement of end C must not exceed 0.17 in. Neglect the weights of the members. Determine the deformation of the steel bar. L = 4 ft A = 0.5 in.2 E 3D 29 х106 psi В A 2 ft 3 ft
Problem 3, The metal stud punch is subjected to a force of 120 N on the handle. Determine the magnitude of the reactive force at the pin A and in the short link BC. Also, determine the resultant internal. loadings acting on the cross section at point E. B 50 mm 100 mm 4 50 mm D 100 mm 200 mm 120 N 300 min
Please don't provide handwritten solution .....
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
A tri-axial state of stress, σx , σy, and σz ,exists in a steel machine part. For steel, E = 200GPa and ν = 0.3. Determine the normal strain in the x-direction if σx = 100MPa, σy = 35MPa, σz = 70MPa. Determine the dilatation. Determine the modulus of rigidity.
2. An elastic block of equal side lengths is deformed into the shape shown by the dashed lines. Determine the shear strain at corner A and at corner C in the deformed position. Ans: -0.026 rad at A, 0.2075 rad at C 3 mm B B D' 53 mm 50 mm 91.5 50 mm 8 mm
The extruded cross section is subjected to a shear force of V = 495 N. Dimensions of the cross section are b = 42 mm, d = 75 mm, and t = 3.0 mm. Determine: (a) the value of Q associated with point H, located at a = 13 mm above the lower surface of the cross section. (b) the magnitude of the horizontal shear stress at point H. (c) the magnitude of the maximum horizontal shear stress in the cross section. ((уp) H a b Answer: (a) QH = 6306 mm3 (b) TH = i 1.091744397 kPa (c) Tmax = 1.637227058 kPa
The link AB of the pliers has the cross section dimensions 3mm x 20mm, and is made of steel with elastic modulus E= 190 GPa. Determine the value of the force F that would cause failure of the link by buckling
5 decimal places Determine the total strain (mm/mm) of a 2.64-m bar with a diameter of 21 mm subjected to a tensile force of 71 kN at a temperature increase of 49 C°. Consider the α=27.3 µm/mC° and E = 122 GPa.
4 m B 4m 8 0.4 m AB X-Section 0.2 mIO (a) Determine to that results in the gap (8) being closed. (b) If w=628 kN/m, determine the internal force in member BC? BC X-Section For the bar shown above, a uniformly distributed axial load wo (force per unit length) is applied between A and B. The diameter of the cross sections AB and BC are also indicated. The material properties of the bar are: E= 20 GPa and 0.3. If the gap 61 mm, then answer the following questions (you can take a 3.14):
The bar has a length of 8 in. and a square cross-sectional 5000 lb 5000 lb area of 0.5 in. x 0.5 in. It is made of a material having the stress-strain diagram shown. If the bar is subjected to an 8 in. σ (ksi) axial force of 5000 lb, determine 75 (a) the change in the 8-in. length, 60 (b) the change in the 0.5-in. thickness. 45 Assume Poisson's ratio is 0.30. 30 15 € (in./in.) 0.001 0.002 0.003 0.004 0.005 0.006 0.007