A flashed steam geothermal powerplant is located where underground hot water is available as saturated liquid at 700 KPa. The well head pressure is 600 KPa. The flashed steam enters a turbine at 500 KPa and expands to 15 KPa. When it is condensed. The flow rate from the well is 29.6 kg/sec. Determine the power produced in KW. Can you show me the solution with a hand written.tnx in advance

A flashed steam geothermal powerplant is located where underground hot water is available as saturated liquid at 700 KPa. The well head pressure is 600 KPa. The flashed steam enters a turbine at 500 KPa and expands to 15 KPa. When it is condensed. The flow rate from the well is 29.6 kg/sec. Determine the power produced in KW. Can you show me the solution with a hand written.tnx in advance

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
HANDWRITTEN and with given, required and solution. Engr. Darmis is tasked to design a frictionless and constant temperature steady-flow system that will be used for power generation using Nitrogen as its working fluid. The initial gage pressure is 110 pounds per square inch and the final volume is 170 cubic feet. If ninety-one pound-mass of the fluid gain 3.253 BTU/R of entropy per minute. Find the (a) initial volume, (b) temperature, and (c) Work. (d) If the heat is equal to 9940 BTU, how long did the process took place?
ı need solution
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. determine the: a. work nonflow and heat transferred
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
The air entering the turbine with 1200 K and 1200 kPa expands to 100 kPa pressure in two stages. When the air is reintroduced to 1200 K at a constant reheat pressure of 350 kPa and both expansion stages are ideally realized: a) Total expansion work (kJ/kg) b) Intermediate heating amount (kJ/kg) c) Calculate the rate of increase in work according to the stepless (without reheating) expansion. Features for air: k=1,4, R=0,287 Jkg K,F1,005 klkg K k = 1.4 R = 0.287 kJ/kgK Cp = 1.005 kJ/kgK %3D
3.) The steam power plant requires 100 gallons per minute to cool the steam in the condenser from an exhaust pressure of 100 kPa. The feedwater pressure is 100 bar and 500 degrees Celsius. The condensate leaves the condenser at saturated liquid. The cooling tower temperature for the leaving cooling water is 25 degrees Celsius and the cooling water leaving the condenser is 42 degrees Celsius. Calculate the mass of the steam in kg/s assuming ideal rankine cycle and standard density of cooling water.
Please solve carefully/ellaborately and include the untis in every step, show diagram and write your solutions clearly and must be readable if your solution is in written form. Your work will be appreaciated much. Thank You.
Answer the problem correctly and provide complete and readable solutions. If you can explain the process (briefly), please do so. Thank you!
Pls. Answer this thank you!Steam enters a turbine stage with an enthalpy of 3628 kj/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kj/kg and a velocity of 124 m/s. Calculate the power in KW if there are 5 kg/s steam admitted at the turbine throttle.
Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
Q1: Steum at a pressure of 28kpa is passed into a condenser and it leawes as condensate at a temperature of sac Cooling water circulates through the condenser at the rate of 45 kg/min - It enters at 152 and Veaves at 3oc If the Steam flow rate is 1.25 eg/min, determinė the drynes fraction of Steam as it enters the condenser.