A flanged bolt coupling consists of eight 12-mm-diameter steel bolts on a bolt circle 400 mm in diameter, and six 12-mm-diameter steel bolts on a concentric bolt circle 300 mm in diameter as shown. Determine the following: P1 200 mm t. P2 150 mm

Q: Q1) A start square (normal series) power screw of 40 mm nominal diameter is acted upon by an axial…

A:

Q: B. If a steel bolt is tested in single shear and fails at a load of 25 kips, at what load would we…

A: single shear force, F=25 kips

Q: (Please input the FBD together with the answer) A flanged bolt coupling consists of nine-in diameter…

A: The torque capacity of the flange coupling is 5522.33 lb•ft.

Q: Fatigue angle in Failure (record number of cycles before failure) Large Metal Paperclip Small Metal…

A: 1.Small metal subjected to a large number of the cycle before failure this is because metal has…

Q: 57 kN axial force acts on the part shaped by the machining method made of xCy steel material. The…

A:

Q: pitch, the torque required for achieving the tightening force is

A: Given data; tightening force=2200 N Pitch=0.004 m

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

A:

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksiThe sleeve CD is…

Q: The required information is in the attachment.  Part A) If the load is at L2 = 4.7 m and the angle…

A:

Q: In a plane strain cutting process, it is found that the coefficient of friction µ (Coulomb) along…

A: Given Data:  Coefficient of friction µ (Coulomb) =1 and independent of the tool rake angle 'a' Rake…

Q: A plate is fastened to a fixed member by four 25 – mm diameter rivets arranged s shown. Compute the…

A: Given Data Fastened diameter, D=25mm=0.025m Distance between 20KN to 20KN is 240mm or 0.240 m Now we…

Q: A 3/8-inch diameter bolt is subjected to a 2,135-lb tensile load. The bolt passes through a very…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm…

A:

Q: A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter…

A: Given Data Diameter of drill bit is : d=5.79 mm=5.79×10-3 m Resisting torque is : T=0.36 N·m…

Q: A 50-mm diameter is fastened to a pulley by means of 12 mm x 12 mm x 60 mm key, as shown in Figure…

A:

Q: From the figure below, what is the rolling resistance from each wheel if they share to carry a…

A: Given data: W=18.7 kN Need to determine the rolling resistance from each wheel and required Force…

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm…

A:

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

A:

Q: ghtening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque requi

A: given:tightening force =2200NPitch=4mm

Q: Referring to Figure Qla, assuming a hollow cylindrical block at the mid-section of the femur with an…

A:

Q: 2. For the lever mechanism shown in the figure below, find the necessary diameter for the bolt of…

A:

Q: A hollow circular shaft with an outside diameter of 50 mm and thickness of 13.5 mm is loaded as…

A:

Q: In a plane strain cutting process, it is found that the coefficient of friction u (Coulomb) along…

A: Given Data:  Coefficient of friction µ (Coulomb) =1 and independent of the tool rake angle 'a' Rake…

Q: d Given: 9/8 in Diameter of bolt = 7/8 inch V2 in Diameter at the root of the thread (bolt) = 0.731…

A:

Q: 2- For the shaft shown, the shear stress is not to exceed 100 MPa. What is most nearly the largest…

A:

Q: Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a…

A:

Q: Shafts A and B are made of the same material and have the same cross-sectional area, but A has a…

A:

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

A:

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: Spindle AB is made of steel with allowable shearing stress of Sleeve CD is made of brass with…

Q: 3. Two ½ in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and…

A: It is asked to find the smallest bolt size to support the load of 55 kips

Q: A flanged bolt coupling consists of eight – 10mm diameter steel bolts on a bolt circle 500mm in…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 120 mm in diameter to a hollow shaft 100 mm…

A:

Q: Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets…

A: Given: Thickness of the sheet (t)=4mmUltimater shear strength of the rivet=500MPaYield shear…

Q: The small gear of an internal gear train shown in the figure is powered by a 500-kW motor at 30 Hz.…

A: Given data:

Q: The formula for Critically Resolved Shear Stress is

A:

Q: If the allowable shear stress is 42 MPa and the allowable angle of twist is 2.5o, what is the…

A: The torque of a shaft can be given by the below formula,

Q: 3. The members of the structure in figure below weigh 280 lb/ft. Determine the smallest diameter pin…

A:

Q: Given the data as shown in the figure, determine the (a) maximum torque Tmax(N·mm) that maybe…

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.