A fisherman has a fish hooked on his line. At first, the pole is horizontal, as shown on the left. Later,the fisherman tilts his pole as shown on the right.2 m--2 m2020100 N100 NConsider an axis of rotation that is perpendicular to the page and passes through the center of thefisherman's hand. In which direction does the torque vector due to the fish point?to the rightto the leftinto the pageout of the pageO There is no torque.

Answered: Image /qna-images/answer/a6b0d02f-d928-463d-87d8-38ba7eefa812.jpg

Answered: A fisherman has a fish hooked on his…

Similar questions

The figure below represents a bicycle wheel comprised of a rim with a radius of R = 0.5 m and mass of M = 200 g, to which someone has added two m = 30 g sensors that are separated by an angle of = 110°. The axis of rotation for the wheel is at its center, as represented by the vector symbol, for a direction into the page. m = 30 g R = 0.5 m M = 200 g m = 30 g a) Where is the center of mass of the wheel/sensor system? b) What is the rotational moment of inertia of the wheel/sensor system around its axis of rotation?
A solid, uniform, spherical boulder (I=(2/5) MR2) starts from rest and rolls down a 75.0 [m] hill, as shown at the figure at the right. The top half of the hill is rough enough to cause the boulder to roll without slipping, but thelower half is covered with ice and there is no friction. What is the translational speed of the boulder when it reaches the bottom of the hill?
A gardener is using a tool as shown in the figure to pull weeds. 24 cm You will notice that the tool is designed with a built-in pivot point about which the torques are applied. If the gardener applies a 1.77 Nm torque (about the pivot point) in order to pull a weed, determine the resistive force (in N) the weed exerts on the weed puller. N
FA740.0N FI-10.0N TO-3 A rotor has four forces applied to it as shown to the right. Find the magnitude and sign of the net (total) torque (about the center of the rotor) on the rotor due to these four forces. Force F4 is applied at the center of the rotor. F3-30ON F220.0N 5.00cm 10.0cm 5.00cm hp
In the image you see a sphere rolling down an inclined plane. Rolling without slipping. Is the weight (mg) producing any torque? Select the correct answer. mg O No O Yes 1P
Two window washers, Bob and Joe, are on a 3.00-m-long, 370-N scaffold supported by two cables attached to its ends. Bob weighs 780 N and stands 1.00 m from the left end, as shown in the figure below. Two meters from the left end is the 500-N washing equipment. Joe is 0.500 m from the right end and weighs 880 N. Given that the scaffold is in rotational and translational equilibrlum, what are the forces on each cable? left cable Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. kN right cable Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. kN Joe Bob 1.00 m- 0.500 m 2.00 m 3.00 m-
A uniform hoop of radius R and mass m rotates freely (without friction) about a perpendicular axis through its rim, as shown. It is released from a position, labeled "Initial", with the hoop's center directly above with the axis. It swings past position "A" where the center is level with the axis and continues swinging through "B" where the center is below the axis. What are the angular accelerations at positions A and B?
A fisherman has a fish hooked on his line. At first, the pole is horizontal, as shown on the left. Later, the fisherman tilts his pole as shown on the right. 2 m- 2 m- 20° 20° 100 N 100 N Consider an axis of rotation that is perpendicular to the page and passes through the center of the fisherman's hand. In which figure is the torque exerted by the fish the largest? In the figure on the left. In the figure on the right. It is the same in both figures. It is impossible to tell from the information given.
A solid disk with an axis of rotation through the center (perpendicular to the diagram). Two holes are cut out near the center and the material is placed near the rim. Which has the larger I? Please explain your conclusion.
A disk is rotating on a horizontal axis as shown in the figure. Answer the following questions if you pull out at A and push in at B along the axis of the disk.What is the direction of the torque acting on the disk? What is the direction of the initial angular momentum vector for the disk? The applied torque causes the wheel's axis (or angular momentum vector) to move. From the front view, what is the direction of motion of the L vector? A disk is rotating on a vertical axis as shown in the figure. Answer the following questions if you push in at A and pull out at B along the axis of the disk. What is the direction of the torque acting on the disk? What is the direction of the initial angular momentum vector for the disk? The applied torque causes the wheel's axis (or angular momentum vector) to move. From the front view, what is the direction of motion of the L vector?
Consider a plywood square mounted on an axis that is perpendicular to the plane of the square and passes through the center of the square. If the square is 0.42 m on a side and is acted on by a 12.5 N force that lies in the plane of the square, determine the magnitude (in N. m) of the maximum torque such a force can produce. N.m
A mass of 0.8 kg is located at the end of a very light and rigid rod 50 cm in length. The rod is rotating about an axis at its opposite end with a rotational velocity of 3 rad/s.a. What is the rotational inertia of the system?b. What is the angular momentum of the system? USe the correct formula to solve and get the right answr.

SEE MORE QUESTIONS