(a) Find the reactive torques at the supports, TA and TB. Use numerical values as follows: da = 2.3 in., L = 43 in., G = 3.4 psi To = 40,000 in.-lb. Round your answers to the nearest whole number. TB in.-lb TA in.-lb (b) Repeat (a) if the hollow section has constant diameter da. Round your answers to the nearest whole number. Тв in.-lb TA in.-lb

Q: Please answer the below  The required formulas are attached

A: Step 1: Given Gs​=75MPa.Gb​=40MPa.db​=90mmNow let the length of the lever at B is 'l' so, the torque…

Q: 1) The steel tube in the system below has an outside radius as listed and an inside diameter of…

A:

Q: A hollow steel shaft, 500 mm outside diameter and 300 mm inside diameter, has a coupling 80 mm thick…

A: Given data: Outside diameter of hollow shaft = 500 mm                    Inside diameter of hollow…

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 3°…

A: Given data:- Angle of twist =3° Length of the shaft =6 m Torque applied =14 kN-m. G = 83 kN/m2 To…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: I need to find the forces in each tube but I keep getting stuck. I have been getting really long…

A: Given:To find:Force in each tube.

Q: 3. A cylindrical rod is composed of two pieces of different diameters. Both pieces are made of the…

A: As per given Question  TB=4000 in-lb TD=3000 in-lb JAC=4 in4 JCD=2 in4 L=10 in G=10×106 We have…

Q: The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn…

A:

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: Diameter of shaft, d = 1 inch.There are 3 forces acting on the beam, 100 lb, 75lb, 80lb.

Q: To use the torsion formula to relate the torque applied to a rod of circular cross section to the…

A:

Q: A B 55² 240 N.mm 420 N.mm 300 N.mm 480 N.mm Figure 1 - Torques applied to the driveshaft 1) DERIVE…

A: Find the  Angle of twist expression Shaft diameter Maximum shear stress

Q: Please show complete work in handwritten format. Don't use chatgpt,If you use Chatgpt it will get a…

A:

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm  D=41mmPCD=63mm

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.