(a) Figure 1 shows a circuit that consists of two silicon diodes, D₁ and D₂. Using ideal model approximation technique, determine the current cross through the diodes, D₁ and D₂ and the output voltage, Vo. Next, perform the same analysis using the Piecewise-Linear equivalent circuit for the diode with a forward resistance value, rav of 592. Finally, compare and discuss the results between ideal and Piecewise-Linear equivalent circuits.

(a) Figure 1 shows a circuit that consists of two silicon diodes, D₁ and D₂. Using ideal model approximation technique, determine the current cross through the diodes, D₁ and D₂ and the output voltage, Vo. Next, perform the same analysis using the Piecewise-Linear equivalent circuit for the diode with a forward resistance value, rav of 592. Finally, compare and discuss the results between ideal and Piecewise-Linear equivalent circuits.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Zener diodes are special purpose diodes designed to operate in their breakdown regions. Describe the working principle and characteristics of a typical Zener diode found in the market place. The Zener-diode regulator circuit shown below is to be used to provide a stabilised output to the load. The zener diode characteristic is also shown. Find the load voltage and source current if the battery voltage is 20 V, series resistance is 1.4 kohm and load resistance is 6 kohm
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Here are some statements about a p-n junction diode. Some are TRUE and some are FALSE. i. Applying a negative bias to the p-side and a positive bias to the n-side allows a forward current flow. ii. When the p-n junction is under reverse bias, the Fermi level is continuous across the junction. iii. The forward bias current is made up of holes from the p-side and electrons from the n-side flowing across the junction. iv. Under reverse bias, you can get minority electrons flowing from the p-side to the n-side of the junction. v. To get a large built-in voltage, you need to heavily dope the p-side and n-side of the junction. vi. The built-in voltage (or contact potential) of a p-n junction is typically twice the value of the band-gap of the semiconductor. Which of the following statements is correct: (i) and (ii) are both FALSE (ii) and (v) are both FALSE (iii) and (vi) are both FALSE
A p-type semiconductor joined to an n-type semiconductor ... Pick those that apply. Will not allow current to flow in either direction. Has electron current flowing from the n-type to the p-type material Makes a diode Allows positive current flow from the p-type to the n-type material
QUESTION 1 Provide an example each for a trivalent and pentavalent element. Describe the doping process of Silicon (Si) to obtain p-type and n-type semiconductor material. a) b) c) Explain forward bias and reverse bias conditions of an ideal p-n junction diode. Sketch the I-V characteristic of Si and Ge diode. Discuss why Si based semiconductor is move favored in production of solid state devices.
Consider a silicon pn junction diode at T 300K. The reverse saturation current is Is = 10-14 A and the ideality factor n = 1. Determine the diode current for a diode voltage of VD = 0.573 V and use that to determine the DC and AC resistance of the diode. RDC = 14.13 k rac = 639 Q RDC = 234 Q2 = rac=8Q RDC = 7.00 KQ rac = 307 Q RDC = 1.43 kQ rac = 58 Q
Current measured in the circuit in the shape created using the ideal diode model .....is. Please select one: a. 0.87 mA b. 1.2 mA c. 0.80 mA d. 0.73 mA
use a P-N junction ideal diode to simulate a circuit measure and plot its I-V characteristics as well as its forward characteristics. assume breakdown voltage of around 6V for your calculations. I have added my multisim design with IV graph of the diode. I need : the large signal piece wise linear parameters of the diode. and for the plot do the theoretical calculations for at least one point on the curve and mark it on the curve This peoblem has other part that I will send when the expert answered this part. Tnx
a) Use the diode’s characteristic equation,ID=Is exp(VD/VT), to determine the currentsourceIso that the output voltage is 1.5 V. b) If a load is attached to the output that draws 1 mA, what is the output voltage? c) If the circuit heats up to 40◦C, what is the output voltage without a load?
....fast and fast..please..
Briefly discuss the difference between Diode Piecewise-linear model, Simplified model, and Ideal device/ equivalent circuit. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each. Discuss briefly how to test junction diode.
Determine the reverse voltage and reverse current for the diode in the Figure below for each of the diode models. Also find the voltage across the limiting resistor in each case. Assume IR = 1-µA. a. The value of reverse current, assuming ideal diode model. b. The value of reverse voltage, assuming ideal diode model. c. The value of voltage across the limiting resistor, assuming ideal diode model. d. The value of reverse current, assuming practical diode model. e. The value of reverse voltage, assuming practical diode model. f. The value of voltage across the limiting resistor, assuming practical diode model. g. The value of reverse current, assuming complete diode model. (in µA) h. The value of reverse voltage, assuming complete diode model. (in mV) i. The value of voltage across the limiting resistor, assuming complete diode model. (in V)