A field measuring 45 m X 90 m is to be prepared using a 1-m upland power tiller at a speed of 3 kph. Assume a 10% overlap between passings and 9 seconds turn around time at the end of each pass. Determine actual field capacity when tilling is done along the shorter field direction: a. 0.23 ha/hr b. 0.25 ha/hr c. 0.27 ha/hr d. 0.29 ha/

Q: P2) The power of a rig drawworks is 300 hp, knowing that 10 lines are strung between the crown block…

A: Given, Power of rig drawworks(Pi)= 300 hp n(number of lines)=10

Q: A cylindrical hole is bored through a steel block, and a cylindrical piston is machined to fit into…

A:

Q: The 20-g bullet is fired horizontally at 900 m/s into the 150-g block resting on a smooth surface.…

A: Given data: mass of the bullet = 20 g                    mass of the block = 150 g…

Q: When a car is rounding a bend on a flat road, the centripetal force is provided by the friction…

A: the free body diagram of car at the turn can be plot as, where r=200m  so,…

Q: #2

A: (a) The given arc length is The given radius of the pulley is The exact angle can be determined…

Q: 6) PLEASE BE CLEAR ON

A: Given that f=220 GHzd=48.8 cm =0.488 mb) Part d=1.96 mλ=1.6 cm

Q: On drawing 31A059, what is dimension H? All abbreviations are standard

A: The flange is defined as the projection used for connecting two different objects like pipes, train…

Q: Cyllndrical tanks are filled with a liquid as shown below. a) ( Calculate the time to completely…

A:

Q: 4) Find i) vertical displacement at C and ii) horizontal displacement at A. Ans: 4A== 14, Pa ZEA…

A:

Q: The change in moment from the left end to A is. W A -1.5 m 3 m- Take w=1 W B +1. -1.5 m-

A: Given      Force, w = 18 kN/m Length, OA = 1.5 m Find   Moment about point A, M

Q: A field measuring 45 m X 90 m is to be prepared using a 1-m upland power tiller at a speed of 3 kph.…

A: Given:45 m X 90 mV=3 Kph10% overlapt=9 sec

Q: this is incorrect Note that n-th geometric cash flow = A1(1+g)^n-1

A: Given:Cost of natural gas in first year,  The cost increment in the next year is the total number of…

Q: M12 X 1.75 k 50.80 101.60 A 203.20 8.30> UNIT:MM CALCULATE THE FF: (SHoW YOUR SOUATION 1. Taper Per…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Assume a T-rex has a leg length of 5m. What is the transitional speed between walking and running of…

A: Given    Length, L = 5 m        Time, t = 1 sec Find   Transitional speed, v

Q: Units are IPS. Just need a general direction on which sketches to make first, which extrusions to…

A: Find Draw the given object step by step.

Q: Draw Shear /moment diagram 200 los/fe 1bs, 50olbs 300bs A I' 1.5' 2'

A:

Q: To remedy the traffic situation at a busy intersection in Mandaluyong City, two plans are being…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.