A fan is used to force air having a temperature of 20°C theough the 200 mm diameter galvanized sheet metal duct. Determine the head added if the length of the duct is 150 m and the flow is to be 0.15m^3/s. Take f=0.023 and kinematic viscosity of air = 15.1x10-6 m²/s.

A fan is used to force air having a temperature of 20°C theough the 200 mm diameter galvanized sheet metal duct. Determine the head added if the length of the duct is 150 m and the flow is to be 0.15m^3/s. Take f=0.023 and kinematic viscosity of air = 15.1x10-6 m²/s.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

correct answer please
20 of 25 Answer: AT = i A solid 0.67-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 23 in., its elastic modulus is E = 29000 ksi, and its coefficient of thermal expansion is a = 7.5 x 10-6 in./in./°F. Determine the temperature increase AT that will cause the rod to buckle. - /2 L -NM ||| B
6 The Reynold number for the flow through smooth pipe is given by 105. The value of friction factor for smooth pipe is
Heavy fuel oil flows at Q = 10 gallons per minute (gpm) in a horizontal steel pipe that connects two storage tanks. The diameter of the pipe is D = 1.5 inches. The length of the pipe is L = 100 feet. The depth of oil in the supply tank is 30 feet above the pipe entrance. The temperature of the oil is 60°F, the specific gravity of the oil is s.g.oin = 0.90, the specific weight of the oil is 56.13 lb/ft', and the kinematic viscosity of the oil is 0.00175 ft2/s. The pipe discharges into the bottom of the receiving tank. Neglect minor losses. a) Determine the pressure p at the pipe entrance in pounds per square foot (psf). b) Determine the velocity v in feet per second (fps). c) Determine the Reynolds number Re. d) Classify the flow based on the Reynolds number Re. e) Determine the Darcy-Weisbach friction factor f. f) Determine the friction head loss hfac in feet in the pipe between the two storage tanks. 8) Determine the depth of oil in feet above the exit from the pipe into the second…
A galvanized-iron pipe (ε = 0.0005 ft) is to carry air at standard temperature and pressure at a rate of 2.0 ft3/s. The pressure drop is to be no more than 0.50 psi per 100 ft. Design the pipe diameter.
In a certain air duct, pressure is being measured in inches of water. The ductis 26 feet long. Find in inches of water per foot the pressure loss in the duct.
I need a handwritten solution, Thank you..
*2-16. Due to its slight compressibility, the density of water varies with depth, although its bulk modulus Eş = 2.20 GPa (absolute) can be considered constant. Accounting for this compressibility, determine the pressure in the water at a depth of 300 m, if the density at the surface of the water is Po = 1000 kg/m. Compare this result with water that is assumed to be incompressible. www.jar
Wrong solution will be downvote
Air in a room at T0 = 290 K and P0 = 90 kPa is to be drawn by a vacuum pump through a 3-cm-diameter, 2-m-long adiabatic tube equipped with a converging nozzle at the inlet. The flow in the nozzle section can be approximated as isentropic. The static pressure is measured to be 87 kPa at the tube inlet and 55 kPa at the tube exit. Determine the mass flow rate of air through the duct, the air velocity at the duct exit, and the average friction factor for the duct.
Why is that the pressure of air P2, the formula is added by 9.81h? Please answer this. Thank you.