A fan delivers 5.1 m^3/sec at a static pressure of 6.167 cm of water when operating at a speed of 603.102 rpm. The power input required is 3.181 kW. If 7.287 m^3/s are desired in the same fan and installation, find the pressure in cm of water Answer in whole number

Q: lic turbine is to ge For initial testing

A:

Q: A pump delivers 10 L/min with a pressure rise of 80 bar. The shaft speed is 1420 rev/min and the…

A:

Q: An impeller of a centrifugal pump runs at 90 rpm under a net head of 10 m and has vanes inclined at…

A: We have provided data from the question are, From the figure we have, N=-90 rpm,ϕ==180-120=60,…

Q: The 32-in diameter pump has a performance curve as below. The pump is used at 1170 rpm in a system…

A:

Q: A piston of double reciprocating pump running at 60 rpm to transport oil of 890 kg/m³. The pump has…

A: Given: The pump speed, N = 60 rpm The density of oil, ρ = 890 kg/m³ The stroke length of pump, L =…

Q: A centrifugal pump is used to lift water from a water reservoir with level 2 m below the pump center…

A:

Q: Find the air horsepower of the AHU fan that delivers 25,000 CFM through a 4ft x 4ft duct with a…

A: To find: The air horsepower of the AHU fan. Given: The flow rate is Q=25,000 CFM1 m60 sec=416.67…

Q: Consider a pitch-regulated, variable speed wind turbine that is 170m in diameter. The cut-in wind…

A: diameter of wind turbine (d) = 170m cut in wind speed = 4m/s rated wind speed = 12m/s cut-out wind…

Q: A centrifugal pump having an overall efficiency of 75%, delivers 1850 liters of water per minute to…

A: Given:Overall efficiency of the pump, η=75 %Water flow rate, Q=1850 L/min=1850×10-360m3/sHeight of…

Q: A certain fan delivers 340 m3/min of air at a static pressure of 25.4 mm of water gage when…

A: Given Data: Volumetric flow rate, Q1=340 m3/min Static pressure head, h1=25.4 mm of water

Q: A 70 cm diameter centrifugal pump which is dynamically similar to the tested pump tabulated above,…

A:

Q: If a pump discharges 85 gpm of water whose specific weight is 61.5 lb/ft (g = 31.95 fps?), find (a)…

A:

Q: An impulse turbine is used to produce hydroelectric power. The average radius of the Pelton wheel is…

A:

Q: Solve step by step Q3. In a Parsons turbine running at 1500 rpm the available enthalpy drop for an…

A: Given Data: Speed of turbine N=1500 rpm Enthalpy drop in expansion of steam ∆H=60 kJ/kg Mean…

Q: to the atmosphere. Estimate the pump power in kW delivered to the water.

A:

Q: The indicated efficiency of a steam engine is 65 %. The engine entrance is 2600 kj/kg and exit is…

A:

Q: Laboratory tests on a centrifugal pump, which is directly coupled to a motor running at constant…

A:

Q: A fan develops 116.84-mm WG static pressure and 21.59-mm velocity head when delivering 317.4 CMM of…

A:

Q: Q3/ A reaction turbine has mean blade speed of 220 m/s and blade speed to steam velocity ratio of…

A: To determine the angle at inlet of blade and work done per kg of steam flow, we can use the…

Q: At atmospheric pressure of 100 kpa exists inside a room. Air is exhausted through a 0.5m diameter…

A: The fan capacity if the operating speed is changed to 1200rpm is 0.667 m3/s.

Q: A turbine is to be built in the south of Jordan for electrical power plant station. As a consultant…

A: Given,

Q: Q5/ A centrifugal pump impeller runs at 1500 rpm & has internal & external diameters of 0.2 n & 0.4…

A: A centrifugal pump is a mechanical device that moves a fluid by transferring rotational energy from…

Q: Q3: a: A centrifugal pump used to take water from reservoir to another through 800 m length and 0.15…

A:

Q: A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a…

A:

Q: A pump has a displacement volume of 6 in^3. It delivers 24 gpm at 1000 rpm and 1000 psi. If the…

A: The displacement volume is The rotational speed is The pressure is The input torque is The discharge…

Q: A reciprocating piston compressor has the following: -Piston diameter of 300mm, -Stroke of 450mm,…

A: Given: Diameter of the piston→D=300 mm=0.30 m Length of the stroke→L=450 mm=0.45 m The PV diagram…

Q: Q1. A centrifugal pump impeller has 0.4m inlet diameter and 0.7 m external diameter. The pump run at…

A:

Q: The diameter of jet of a turbojet is 2.5 m and it flies at 500 km/h at an elevation of 8 km for…

A: Given Data : Diameter of Jet dj = 2.5 m speed u= 500 km/h = 138.89 m/s Elevation z = 8 Km = 8000m…

Q: The following creep data were taken on an aluminum alloy at 480 °C and a constant stress of 2.75…

A: To plot the given data and calculate the steady-state or minimum creep rate.

Q: The power (in MW) of a full sized

A: Given; A test conducted on a 1/5 scale model of a francis turbine under a head ,h=2mVolumetric flow…

Q: ind the pressure in cm of water

A: Given: Q1=5.226 m3/s P1=h1=6.895 cm N1=450.941 rpm P1=3.97 kW Q2=9.15 m3/s To determine:  The…

Q: centrifugal pump operating under steady flow conditions delivers 228 initial pressure of 82720 Pa to…

A: Given data as per question Mass flow rate of water, m˙=2285 kg/min Initial Pressure, P1=82720 Pa…

Q: Beam deflection is to the length to a beam. OA. flexure

A: Explanation As we know that the deflection of any beam always follow the equation of elastic curve…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.