A factory has an electrical load of 1600kW at a lagging power factor of 0.8. An additional variable power factor load is to be added to the factory. The new load will add 320kW to the real power load of the factory. The power factor of the added load is to be adjusted so that the overall power factor of the factory is 0.96 lagging. a. Specify the reactive power associated with the added load. b. What is the power factor of the additional load?

A factory has an electrical load of 1600kW at a lagging power factor of 0.8. An additional variable power factor load is to be added to the factory. The new load will add 320kW to the real power load of the factory. The power factor of the added load is to be adjusted so that the overall power factor of the factory is 0.96 lagging. a. Specify the reactive power associated with the added load. b. What is the power factor of the additional load?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
please answer alll subparts for like either dislike... 1. Find the total real power supplied by the source 2. The total reactive power supplied by the source is 3. The magnitude of the total apparent power is 4. The power factor of the source is 5. A capacitor is connected across the loads as indicated in Figure 1 to improve the power factor to 0.95 pf lagging The required reactive power supplied by the capacitor is 6. The value of the capacitor is
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following: e. Reactive power supplied by the sourcef. Apparent power of the circuitg. Power factor of the entire circuit
The variable resistor R in the circuit is adjusted until it absorbs the maximum average power. * The value of the load resistance that maximize the power transfer is... ohms 32 -j22 H j12 4/0° A R. 4.3 O 1.23 O 2.58 O 5.94 none of the above O 7.81 O
Which one of the following statements is true: The purpose of the power-factor correction is to add inductive elements to keep real power at a minimum level. The purpose of the power-factor correction is to add resistive elements (typically resistances) to improve the total reactive power. The purpose of the power-factor correction is to add reactive components (typically capacitive) to establish a system power factor closer to unity. The purpose of the power-factor correction is to add resistive elements (typically resistances) to establish a system power factor closer to zero.
Two loads are connected in parallel to a 1000 v(rms) 60Hz source. One of the loads has an average power of 500 kW and a forward power factor of 0.9. Since the other load absorbs 400kw and 600kvar power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) Find the value of the capacitor to be connected parallel to the loads so that the power factor is 0.95 back d) Find and compare the magnitude of the current drawn from the .source for the situations before and after the capacitor is connected not: Please solve this question in detail, in a way that I can understand
A load is supplied by a 230 V, 50 Hz source. The active power P and the reactive power Q consumed by the load are such that 1 kW SPS2 kW and 1 KVAR SQS2 KVAR. A capacitor connected across the load for power factor correction generates 1 KVAR reactive power. The worst case power factor after power factor connection is Options: 1. 0.447 lag 2. 0.707 lag 3. 0.894 lag 4.1
A particular load has a pt of 0.78 lagging.The power delivered to the load is 36KW from a 240V rms 60Hz line. If 200μF capacitor is placed in parallel with the load, What is the new power factor of the total load. Select one: O a. 0.826 logging. O b. 0.5 leading. O c.0.94 logging O d. 0.7 leading.
For a source which has load has the following characteristics: • Vrms = 125 20° V • P= 400 W • pf = 0.925 lagging What is the rms current and reactive power?
i need the answer quickly
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…
To improve a lagging power factor: a the apparent power from the source is increased. the reactive power from the source is increased. C a capacitor is placed in parallel with the load. C) the source current is increased.