Please need within 30 minThank you. "A face milling operation is performed to finishthe top surface of a steel rectangular workpiece11 in long by 3 in wide. The milling cutter has 6teeth (cemented carbide inserts) and a 5 indiameter. Cutting conditions are: v = 461 ft/min, f= 0.04 in/tooth, and d = 0.2 in. The cutter is offsetto one side so that the swath cut by the cutter 1 inwide. Determine: the material removal rate for thisoperation. Units: min3/min"

Answered: Image /qna-images/answer/32544cc7-d6bb-4c9e-99c3-ae187e209110.jpg

Answered: "A face milling operation is performed…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Project 7: In this project you were assigned to explore your mechanical design and system capabilities. Your manger asked you to prepare a technical research report to evaluate the effects of misalignment of shafts and the measures that are taken to prevent problems from occurring. The hiring committee asked you to deliver a short report showing your evaluation (no more than 600 words).
The final answer must be correct otherwise leave . Don't provide wrong answer ,It will be downvoted.
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Summary/Conclusion Discuss the strengths of your design and how it met the specifications. Discuss your assumptions and why they are valid. Discuss what you might change about your design in a redesign effort. Format: The project should be presented as a design report using a word processor. Include any hand calculations in an appendix. More details will be provided. Choose to design either a slip-jaw or channel-lock pliers to last for 25 years of use by a professional. Use an appropriate tool steel for the pliers. Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not given. Slip Jaw Pliers A= 9.00 inches B=1.00 inches C= ? D=1.25 inches H= 1.875 Inches D B A
In the last few steps, where did 0.4 come from?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS